hdparm: SECURITY_SET_PASS: 입출력 오류

hdparm: SECURITY_SET_PASS: 입출력 오류

나는 hdparm사용하려고보안 삭제SSD를 권장합니다여기.

지금까지는 해당 가이드의 지침에 따라 모든 것이 잘 작동하고 있지만 이 오류를 해결할 수 없는 것 같습니다.

~ $ sudo hdparm --user-master m --security-set-pass NUL /dev/sda
security_password="NUL"

/dev/sda:
 Issuing SECURITY_SET_PASS command, password="NUL", user=master, mode=high
SECURITY_SET_PASS: Input/output error

제안대로 검색하고 테스트했습니다.여기, 그러나 소용이 없습니다. 이것이 옵션이 아닌 경우 SSD를 완전히 지우려면 어떻게 해야 합니까?

참고: 예, 부팅 시 입력해야 하기 때문에 하드 드라이브 "에" BIOS 암호가 있지만 (내가 아는 한) 디스크 자체에는 연결되어 있지 않습니다.


sudo hdparm -I /dev/sda:

/dev/sda:

ATA device, with non-removable media
    Model Number:       SanDisk SDSSDA240G                      
    Serial Number:      153655402044        
    Firmware Revision:  U21010RL
    Media Serial Num:   
    Media Manufacturer: 
    Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
    Used: unknown (minor revision code 0x0110) 
    Supported: 9 8 7 6 5 
    Likely used: 9
Configuration:
    Logical     max current
    cylinders   16383   16383
    heads       16  16
    sectors/track   63  63
    --
    CHS current addressable sectors:   16514064
    LBA    user addressable sectors:  268435455
    LBA48  user addressable sectors:  468862128
    Logical  Sector size:                   512 bytes
    Physical Sector size:                   512 bytes
    Logical Sector-0 offset:                  0 bytes
    device size with M = 1024*1024:      228936 MBytes
    device size with M = 1000*1000:      240057 MBytes (240 GB)
    cache/buffer size  = unknown
    Form Factor: 2.5 inch
    Nominal Media Rotation Rate: Solid State Device
Capabilities:
    LBA, IORDY(can be disabled)
    Queue depth: 32
    Standby timer values: spec'd by Standard, no device specific minimum
    R/W multiple sector transfer: Max = 1   Current = 1
    Advanced power management level: disabled
    DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
         Cycle time: min=120ns recommended=120ns
    PIO: pio0 pio1 pio2 pio3 pio4 
         Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
    Enabled Supported:
       *    SMART feature set
       *    Security Mode feature set
       *    Power Management feature set
       *    Write cache
            Look-ahead
       *    Host Protected Area feature set
       *    WRITE_BUFFER command
       *    READ_BUFFER command
       *    DOWNLOAD_MICROCODE
            Advanced Power Management feature set
            SET_MAX security extension
       *    48-bit Address feature set
       *    Device Configuration Overlay feature set
       *    Mandatory FLUSH_CACHE
       *    FLUSH_CACHE_EXT
       *    SMART error logging
       *    SMART self-test
       *    General Purpose Logging feature set
       *    WRITE_{DMA|MULTIPLE}_FUA_EXT
       *    64-bit World wide name
       *    {READ,WRITE}_DMA_EXT_GPL commands
       *    Segmented DOWNLOAD_MICROCODE
       *    Gen1 signaling speed (1.5Gb/s)
       *    Gen2 signaling speed (3.0Gb/s)
       *    Gen3 signaling speed (6.0Gb/s)
       *    Native Command Queueing (NCQ)
       *    Host-initiated interface power management
       *    Phy event counters
       *    READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
       *    DMA Setup Auto-Activate optimization
            Device-initiated interface power management
       *    Software settings preservation
            Device Sleep (DEVSLP)
       *    Data Set Management TRIM supported (limit 8 blocks)
Security: 
    Master password revision code = 11822
        supported
        enabled
        locked
    not frozen
    not expired: security count
        supported: enhanced erase
    Security level high
    2min for SECURITY ERASE UNIT. 2min for ENHANCED SECURITY ERASE UNIT. 
Logical Unit WWN Device Identifier: 5001b44ed2285a3c
    NAA     : 5
    IEEE OUI    : 001b44
    Unique ID   : ed2285a3c
Checksum: correct
Device Sleep:
    DEVSLP Exit Timeout (DETO): 70 ms (drive)
    Minimum DEVSLP Assertion Time (MDAT): 31 ms (drive)

답변1

내 컴퓨터의 BIOS에 비밀번호가 있습니다.

비밀번호를 제거하고 재부팅한 후 위 명령을 다시 시도하면 문제가 해결되었습니다.

내 BIOS에 비밀번호가 다시 있습니다.

관련 정보