SSD가 데이터를 잊어버리고 이전 버전으로 롤백합니다.
아치 포럼에 이런 질문을 올렸습니다.여기.
앱을 설치했는데 모든 것이 잘 작동한다고 가정해 보겠습니다. 그런 다음 재부팅한 후 모든 구성, 관련 데이터 등을 포함하여 완전히 사라졌습니다. 예를 들어 fstab을 구성할 때도 이런 일이 발생합니다. 재부팅 후 이전 버전으로 돌아 왔습니다.
재부팅을 한 번 더 하면 다시 "새" 구성으로 돌아갑니다. "이전" 버전으로 세 번째 재부팅합니다. 따라서 사실 내 시스템에는 두 가지 버전이 있으며 재부팅할 때마다 두 버전 간에 전환됩니다.
다음 주에 새 SSD에 복사하여 이 구성을 테스트하겠습니다.
Linux ThijsPC 3.17.1-1-ARCH #1 SMP PREEMPT Wed Oct 15 15:04:35 CEST 2014 x86_64 GNU/Linux
디스크의 30%만 분할됩니다. TRIM이 활성화되었습니다. cfq I/O 스케줄러를 사용합니다. 드라이브는 3년 된 Crucial-M4입니다.
UUID=2bddf92c-de9e-4bbc-bec9-5ba848dea11c / ext4 rw,defaults,noatime,discard 0 1
tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0
나는 팔로우한다이 위키문제 해결에 사용됩니다.
root@thijspc .:08:38:. {thijs}>hdparm -I /dev/sdc | grep TRIM
* Data Set Management TRIM supported (limit 8 blocks)
* Deterministic read data after TRIM
그리고:
[root@thijspc ~]# cat /sys/block/sdc/queue/scheduler
noop deadline [cfq]
디스크 드라이브
Disk /dev/sdc: 238.5 GiB, 256060514304 bytes, 500118192 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 04171B1D-F083-4569-AFD9-5AC6B38C6063
Device Start End Sectors Size Type
/dev/sdc1 2048 204802047 204800000 97.7G Linux filesystem
/dev/sdc2 204802048 204804095 2048 1M BIOS boot
dmesg의 grep 'ata'(ata4)
[ 0.000000] ACPI: SSDT 0x00000000DDE30378 00036D (v01 SataRe SataTabl 00001000 INTL 20120711)
[ 0.000000] Memory: 16374176K/16718360K available (5381K kernel code, 909K rwdata, 1712K rodata, 1140K init, 1176K bss, 344184K reserved)
[ 0.799859] Write protecting the kernel read-only data: 8192k
[ 0.847719] libata version 3.00 loaded.
[ 0.902244] ata1: SATA max UDMA/133 abar m2048@0xf7f16000 port 0xf7f16100 irq 27
[ 0.902245] ata2: DUMMY
[ 0.902246] ata3: SATA max UDMA/133 abar m2048@0xf7f16000 port 0xf7f16200 irq 27
[ 0.902248] ata4: SATA max UDMA/133 abar m2048@0xf7f16000 port 0xf7f16280 irq 27
[ 0.902251] ata5: SATA max UDMA/133 abar m2048@0xf7f16000 port 0xf7f16300 irq 27
[ 0.902254] ata6: SATA max UDMA/133 abar m2048@0xf7f16000 port 0xf7f16380 irq 27
[ 0.902845] ata7: SATA max UDMA/133 abar m512@0xf7b00000 port 0xf7b00100 irq 28
[ 0.902848] ata8: SATA max UDMA/133 abar m512@0xf7b00000 port 0xf7b00180 irq 28
[ 1.220536] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.220545] ata7: SATA link down (SStatus 0 SControl 300)
[ 1.220557] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.220573] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
FSCK
fsck from util-linux 2.25.1
e2fsck 1.42.12 (29-Aug-2014)
Warning! /dev/sdc1 is mounted.
Warning: skipping journal recovery because doing a read-only filesystem check.
Pass 1: Checking inodes, blocks, and sizes
Deleted inode 31002 has zero dtime. Fix? no
Inodes that were part of a corrupted orphan linked list found. Fix? no
Inode 31010 was part of the orphaned inode list. IGNORED.
Inode 31060 was part of the orphaned inode list. IGNORED.
Inode 31199 was part of the orphaned inode list. IGNORED.
Inode 4075151 was part of the orphaned inode list. IGNORED.
Inode 4075224 was part of the orphaned inode list. IGNORED.
Inode 4075385 was part of the orphaned inode list. IGNORED.
Inode 4075637 was part of the orphaned inode list. IGNORED.
Inode 4075641 was part of the orphaned inode list. IGNORED.
Inode 4075873 was part of the orphaned inode list. IGNORED.
Inode 4075874 was part of the orphaned inode list. IGNORED.
Inode 4075944 was part of the orphaned inode list. IGNORED.
Inode 4075968 was part of the orphaned inode list. IGNORED.
Inode 4075973 was part of the orphaned inode list. IGNORED.
Pass 2: Checking directory structure
Entry 'E575FA3D8C4DFC93DCE2C4BD0E4E6B4B928AE50E' in /home/thijs/.cache/mozilla/firefox/ltoaq0gi.default/cache2/entries (5269454) has deleted/unused inode 5284764. Clear? no
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Block bitmap differences: -(1684521--1684524) -(1685190--1685198) -(2181790--2181798) -(7614052--7614054) -(7615072--7615074) -(7620243--7620250) -(11070148--11070151) -16529433 -(16529439--16529447) -(21100591--21100598) -(21100641--21100648)
Fix? no
Free blocks count wrong (12652279, counted=12643997).
Fix? no
Inode bitmap differences: -31002 -31010 -31060 -31199 -4075151 -4075224 -4075385 -4075637 -4075641 -(4075873--4075874) -4075944 -4075968 -4075973 -5284764
Fix? no
Free inodes count wrong for group #645 (572, counted=571).
Fix? no
Free inodes count wrong (5515652, counted=5511054).
Fix? no
/dev/sdc1: ********** WARNING: Filesystem still has errors **********
890492 inodes used (13.90%, out of 6406144)
2070 non-contiguous files (0.2%)
365 non-contiguous directories (0.0%)
# of inodes with ind/dind/tind blocks: 0/0/0
Extent depth histogram: 869562/388/1
12947720 blocks used (50.58%, out of 25599999)
0 bad blocks
2 large files
514993 regular files
339635 directories
0 character device files
0 block device files
2 fifos
2340 links
40434 symbolic links (25112 fast symbolic links)
2 sockets
------------
897407 files
그리고 smartctl -a
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.17.1-1-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Crucial/Micron RealSSD m4/C400/P400
Device Model: M4-CT256M4SSD2
Serial Number: 0000000012530922F762
LU WWN Device Id: 5 00a075 10922f762
Firmware Version: 040H
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Nov 17 15:36:20 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 300) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 19) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 050 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 100 100 001 Old_age Always - 4240
12 Power_Cycle_Count 0x0032 100 100 001 Old_age Always - 1010
170 Grown_Failing_Block_Ct 0x0033 100 100 010 Pre-fail Always - 0
171 Program_Fail_Count 0x0032 100 100 001 Old_age Always - 0
172 Erase_Fail_Count 0x0032 100 100 001 Old_age Always - 0
173 Wear_Leveling_Count 0x0033 099 099 010 Pre-fail Always - 38
174 Unexpect_Power_Loss_Ct 0x0032 100 100 001 Old_age Always - 68
181 Non4k_Aligned_Access 0x0022 100 100 001 Old_age Always - 520 386 134
183 SATA_Iface_Downshift 0x0032 100 100 001 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 001 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 001 Old_age Always - 0
189 Factory_Bad_Block_Ct 0x000e 100 100 001 Old_age Always - 80
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 0
195 Hardware_ECC_Recovered 0x003a 100 100 001 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 100 100 001 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 001 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 001 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 100 100 001 Old_age Always - 0
202 Perc_Rated_Life_Used 0x0018 099 099 001 Old_age Offline - 1
206 Write_Error_Rate 0x000e 100 100 001 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor (0xff) Completed without error 00% 4232 -
# 2 Vendor (0xff) Completed without error 00% 4219 -
# 3 Vendor (0xff) Completed without error 00% 1702 -
# 4 Vendor (0xff) Completed without error 00% 1277 -
# 5 Short offline Completed without error 00% 1218 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
애벌레
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-simple-2bddf92c-de9e-4bbc-bec9-5ba848dea11c' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_gpt
insmod ext2
set root='hd2,gpt1'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd2,gpt1 --hint-efi=hd2,gpt1 --hint-baremetal=ahci2,gpt1 2bddf92c-de9e-4bbc-bec9-5ba848dea11c
else
search --no-floppy --fs-uuid --set=root 2bddf92c-de9e-4bbc-bec9-5ba848dea11c
fi
echo 'Loading Linux linux ...'
linux /boot/vmlinuz-linux root=UUID=2bddf92c-de9e-4bbc-bec9-5ba848dea11c rw quiet
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux.img
}
답변1
SSD 불량일 가능성이 높습니다. LiveCD에서 이 동작을 재현할 수 있습니까? (fsck, 마운트, 일부 데이터 쓰기, 마운트 해제, LiveCD 다시 시작, 마운트, 데이터 확인...) 동일한 문제가 표시되면 SSD 또는 파일 시스템이 손상되어 fsck가 실제로 문제를 해결할 수 없을 가능성이 있습니다.
Live CD에서 이런 일이 발생하지 않으면 커널이나 설치된 시스템이 어떤 이유로든 재부팅 시 제대로 제거/새로 고침되지 않는 등 다른 문제가 원인일 수 있습니다.
귀하의 SMART 번호는 정렬되지 않은 4k 액세스를 제외하고는 이상하게 보이지 않습니다. 귀하의 값은 내 Crucial M4보다 더 큰 것 같습니다. 파티션이 정렬되어 있나요? 그렇지 않더라도 이러한 오류가 발생해서는 안 됩니다.