내 Toshiba 1TB 외부 장치가 계속 잠자기 상태이고 대기 매개변수와 유사한 항목을 찾을 수 없는 것 같습니다. 이 잠에 대한 충동을 멈추는 방법을 아는 사람이 있습니까? 출력은 다음과 같습니다 sdparm -a /dev/sdc.
sudo sdparm -a /dev/sdc
/dev/sdc: TOSHIBA External USB 3.0 0001
Read write error recovery mode page:
AWRE 1 [cha: n, def: 1, sav: 0]
ARRE 0 [cha: n, def: 0, sav: 0]
TB 0 [cha: n, def: 0, sav: 0]
RC 0 [cha: n, def: 0, sav: 0]
EER 0 [cha: n, def: 0, sav: 0]
PER 0 [cha: n, def: 0, sav: 0]
DTE 0 [cha: n, def: 0, sav: 0]
DCR 0 [cha: n, def: 0, sav: 0]
RRC 3 [cha: n, def: 3, sav: 0]
COR_S 0 [cha: n, def: 0, sav: 0]
HOC 0 [cha: n, def: 0, sav: 0]
DSOC 0 [cha: n, def: 0, sav: 0]
LBPERE 0 [cha: n, def: 0, sav: 0]
WRC 3 [cha: n, def: 3, sav: 0]
RTL 0 [cha: n, def: 0, sav: 0]
Caching (SBC) mode page:
IC 0 [cha: n, def: 0, sav: 0]
ABPF 0 [cha: n, def: 0, sav: 0]
CAP 0 [cha: n, def: 0, sav: 0]
DISC 0 [cha: n, def: 0, sav: 0]
SIZE 0 [cha: n, def: 0, sav: 0]
WCE 0 [cha: n, def: 0, sav: 0]
MF 0 [cha: n, def: 0, sav: 0]
RCD 0 [cha: n, def: 0, sav: 0]
DRRP 0 [cha: n, def: 0, sav: 0]
WRP 0 [cha: n, def: 0, sav: 0]
DPTL 0 [cha: n, def: 0, sav: 0]
MIPF 0 [cha: n, def: 0, sav: 0]
MAPF 0 [cha: n, def: 0, sav: 0]
MAPFC 0 [cha: n, def: 0, sav: 0]
FSW 0 [cha: n, def: 0, sav: 0]
LBCSS 0 [cha: n, def: 0, sav: 0]
DRA 1 [cha: n, def: 1, sav: 0]
NV_DIS 0 [cha: n, def: 0, sav: 0]
NCS 0 [cha: n, def: 0, sav: 0]
CSS 0 [cha: n, def: 0, sav: 0]
Informational exceptions control mode page:
PERF 0 [cha: n, def: 0, sav: 0]
EBF 0 [cha: n, def: 0, sav: 0]
EWASC 0 [cha: n, def: 0, sav: 0]
DEXCPT 0 [cha: n, def: 0, sav: 0]
TEST 0 [cha: n, def: 0, sav: 0]
EBACKERR 0 [cha: n, def: 0, sav: 0]
LOGERR 0 [cha: n, def: 0, sav: 0]
MRIE 6 [cha: n, def: 6, sav: 0]
INTT 0 [cha: n, def: 0, sav: 0]
Background control (SBC) mode page:
S_L_FULL 0 [cha: n, def: 0, sav: 0]
LOWIR 0 [cha: n, def: 0, sav: 0]
EN_BMS 0 [cha: n, def: 0, sav: 0]
EN_PS 0 [cha: n, def: 0, sav: 0]
BMS_I 0 [cha: n, def: 0, sav: 0]
Logical block provisioning (SBC) mode page:
SITUA 0 [cha: n, def: 0, sav: 0]
다음은 작동하는 것으로 보이며 드라이브가 다시 최대 절전 모드로 전환되면 이 질문을 업데이트하겠습니다.
sudo hdparm --prefer-ata12 -S 0 /dev/sdc
/dev/sdc:
setting standby to 0 (off)
SG_IO: bad/missing sense data, sb[]: f0 00 01 00 50 40 00 0a 00 00 00 00 00 1d 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00