TP-Link Archer T2UH AC600 무선 어댑터를 구입했고 드라이버를 제대로 컴파일할 수 있었지만 지금 직면한 문제는 파일입니다 RT2870STA.dat. Linux 시스템용 TP-Link에서 제공하는 매뉴얼의 지침을 따르려고 했지만 빈 필드를 처리하는 방법이 혼란스럽고 대부분의 필드가 무엇을 의미하는지 이해하지 못합니다.
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=CA
SSID=Rogers343 <--#nomyreal SSID
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=NONE
WPAPSK=1234567
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
EthConvertMode=
EthCloneMac=
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
MeshId=MESH
MeshAutoLink=1
MeshAuthMode=OPEN
MeshEncrypType=NONE
MeshWPAKEY=
MeshDefaultkey=1
MeshWEPKEY=
CarrierDetect=0
빈 필드도 있고 거기에 어떤 값이 있는지 모르겠습니다. 내 Wi-Fi 연결 이름 이 SSID변경 . CountryCode캐나다에서 내 가치가 얼마인지 잘 모르겠습니다 . 현재 사용 중인 Wi-Fi 연결이므로 입력 해야 AuthMode할 것 같습니다 . 파일에는 자동으로 아무것도 없습니다 . 그것이 무엇인지 잘 모르겠습니다. 내 비밀번호가 될 것입니다. 다른 빈 필드가 많이 있는데 어떻게 해야 할지 모르겠습니다. iwpriv를 사용하여 Kali Linux에서 무선 어댑터를 설정하려고 하는데 계속 하기 전에 해당 구성으로 이동해야 하기 때문입니다 . 또한 dhclient를 사용하여 IP를 요청할 수 있으려면 액세스 포인트의 SSID를 구성해야 합니다. 내 질문은 AP의 SSID를 얻는 방법입니다. wlan0 인터페이스의 값과 ra0 인터페이스의 값을 비교해 보면 wlan0 액세스 포인트가 MAC 주소처럼 보이지만 어댑터에 MAC 주소가 보이지 않고 어떤 값을 넣어야 할지 모르겠습니다. 그것. 어댑터를 설정하기 위해 수행한 단계는 다음과 같습니다.WPAWPA2PersonalEncrypTypeWPAPSKRT2870STA.dat/etc/Wireless/RT2870STA/RT2870STA.datiwpriv
iwpriv ra0 set NetworkType=Infra
iwpriv ra0 set AuthMode=WPA2PSK
iwpriv ra0 set EncrypType=TKIP
iwpriv ra0 set SSID="Rogers343"
iwpriv ra0 set WPAPSK=1234567 <-- not my acutal pswd
iwpriv ra0 set WirelessMode=14
이러한 명령을 입력하면 iwconfig ra0다음이 표시됩니다.
Ralink STA ESSID:"Rogers343" Nickname:"MT7610U_STA"
Mode:Auto Frequency=5.18 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=10/100 Signal level:0 dBm Noise level:0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
dmesg어댑터가 연결되면 출력됩니다.
3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074177] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 3633.074178] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.832271] #
[ 4260.834242] receive cmd msg fail(-71)
[ 4260.838494] receive cmd msg fail(-71)
[ 4260.841272] #
[ 4260.842743] receive cmd msg fail(-71)
[ 4260.846994] receive cmd msg fail(-71)
[ 4260.850247] #
[ 4260.851243] receive cmd msg fail(-71)
[ 4260.855520] receive cmd msg fail(-71)
[ 4260.859274] #
[ 4260.996257] receive cmd msg fail(-71)
[ 4260.998887] #
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.030639] #
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
그런 다음 이 작업을 수행했는데 systemctl restart network-manager.service
네트워크에서 쫓겨났지만 네트워크 관리자에 두 Wi-Fi 아이콘이 모두 나타나는 것을 볼 수 있었지만 아래 이미지에 표시된 것처럼 두 카드 모두 "사용할 수 없음"이라고 표시되고 네트워크가 선택되지 않습니다.
dmesg이 일이 발생한 후의 결과입니다.
238.916761] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2)
[ 238.916766] bluetooth hci0: Direct firmware load for brcm/BCM.hcd failed with error -2
[ 238.916769] Bluetooth: hci0: BCM: Patch brcm/BCM.hcd not found
[ 239.115808] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.310935] r8169 0000:07:00.0 eth0: link down
[ 239.310991] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.311865] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 240.719041] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[ 240.719043] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[ 285.069677] ERROR @wl_notify_scan_status : wlan0 Scan_results error (-22)
[ 954.235212] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1193.231540] perf: interrupt took too long (3135 > 3132), lowering kernel.perf_event_max_sample_rate to 63750
[ 1470.857282] perf: interrupt took too long (4013 > 3918), lowering kernel.perf_event_max_sample_rate to 49750
[ 2345.359889] perf: interrupt took too long (5032 > 5016), lowering kernel.perf_event_max_sample_rate to 39500
[ 3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074170] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 3633.074171] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.808616] receive cmd msg fail(-71)
[ 4260.812867] receive cmd msg fail(-71)
[ 4260.817116] receive cmd msg fail(-71)
[ 4260.898248] receive cmd msg fail(-71)
[ 4260.900248] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4260.902500] receive cmd msg fail(-71)
[ 4260.904250] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.945005] receive cmd msg fail(-71)
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
[ 5382.065830] -->RTUSBVenderReset
[ 5382.066025] <--RTUSBVenderReset
[ 5382.070992] fw version:0.1.00 build:7640
[ 5382.070994] build time:201308221655____
[ 5382.071000] ilm length = 68780(bytes)
[ 5382.071000] dlm length = 11476(bytes)
[ 5382.152631] #
[ 5382.158632] loading fw......
[ 5382.276688] #
[ 5382.494398] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 5382.494400] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 5382.494401] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 5382.494402] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 5382.494408] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5382.494409] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5382.494466] cfg_mode=5
[ 5382.494468] wmode_band_equal(): Band Not Equal!
[ 5382.494582] Key1Str is Invalid key length(0) or Type(0)
[ 5382.494593] Key2Str is Invalid key length(0) or Type(0)
[ 5382.494604] Key3Str is Invalid key length(0) or Type(0)
[ 5382.494616] Key4Str is Invalid key length(0) or Type(0)
[ 5382.494856] 1. Phy Mode = 31
[ 5382.494856] 2. Phy Mode = 31
[ 5382.494858] NVM is Efuse and its size =1d[1e0-1fc]
[ 5382.506903] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5382.517405] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5382.521530] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5382.521531] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5382.521532] Temperature Tx ALC not enabled
[ 5382.537531] 3. Phy Mode = 31
[ 5382.537533] AntCfgInit: primary/secondary ant 0/1
[ 5382.542790] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5382.544283] MCS Set = ff 00 00 00 01
[ 5382.554214] <==== rt28xx_init, Status=0
[ 5382.555157] 0x1300 = 00064300
[ 5382.555158] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5382.555314] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5482.218330] ===>rt_ioctl_giwscan. 2(2) BSS returned, data->length = 317
[ 5550.260554] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5550.293209] ERROR!!! RTMPSetTimer failed, Halt in Progress!
[ 5550.300208] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003
[ 5550.303830] receive cmd msg fail(-2)
[ 5550.303842] tx_kickout_fail_count = 0
[ 5550.303844] tx_timeout_fail_count = 0
[ 5550.303845] rx_receive_fail_count = 0
[ 5550.303846] alloc_cmd_msg = 6981
[ 5550.303846] free_cmd_msg = 6981
[ 5550.359595] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000
[ 5550.366721] -->RTUSBVenderReset
[ 5550.366846] <--RTUSBVenderReset
[ 5550.371809] fw version:0.1.00 build:7640
[ 5550.371811] build time:201308221655____
[ 5550.371825] ilm length = 68780(bytes)
[ 5550.371825] dlm length = 11476(bytes)
[ 5550.451175] #
[ 5550.457901] loading fw......
[ 5550.796383] RTMP_TimerListAdd: add timer obj ffffc64740b38d18!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27b80!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27bf8!
[ 5550.796385] RTMP_TimerListAdd: add timer obj ffffc64740b38e88!
[ 5550.796386] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5550.796387] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5550.796444] cfg_mode=5
[ 5550.796446] wmode_band_equal(): Band Not Equal!
[ 5550.796559] Key1Str is Invalid key length(0) or Type(0)
[ 5550.796570] Key2Str is Invalid key length(0) or Type(0)
[ 5550.796581] Key3Str is Invalid key length(0) or Type(0)
[ 5550.796592] Key4Str is Invalid key length(0) or Type(0)
[ 5550.796832] 1. Phy Mode = 31
[ 5550.796833] 2. Phy Mode = 31
[ 5550.796834] NVM is Efuse and its size =1d[1e0-1fc]
[ 5550.807751] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5550.818252] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5550.822377] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5550.822378] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5550.822378] Temperature Tx ALC not enabled
[ 5550.839378] 3. Phy Mode = 31
[ 5550.839379] AntCfgInit: primary/secondary ant 0/1
[ 5550.844637] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5550.846035] MCS Set = ff 00 00 00 01
[ 5550.855972] <==== rt28xx_init, Status=0
[ 5550.857128] 0x1300 = 00064300
[ 5550.857129] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5550.857255] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5551.014244] BUG: unable to handle kernel paging request at 00007fff13453d00
[ 5551.014316] IP: [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.014402] PGD 116cca067 PUD 11599c067 PMD 117fd0067 PTE 800000010a6d3867
[ 5551.014467] Oops: 0001 [#1] SMP
[ 5551.014494] Modules linked in: fuse nfnetlink_queue nfnetlink_log nfnetlink binfmt_misc wl(PO) mt7650u_sta(O) snd_hda_codec_hdmi intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp btusb btrtl btbcm btintel uvcvideo bluetooth videobuf2_vmalloc kvm_intel dcdbas videobuf2_memops iTCO_wdt snd_hda_codec_realtek videobuf2_v4l2 iTCO_vendor_support kvm hid_rmi dell_smm_hwmon videobuf2_core videodev irqbypass snd_hda_codec_generic cfg80211 snd_hda_intel rtsx_usb_ms hid_multitouch memstick pcspkr media snd_soc_rt5640 snd_hda_codec snd_soc_ssm4567 snd_soc_rl6231 snd_soc_core snd_hda_core joydev evdev snd_hwdep snd_compress snd_pcm sg serio_raw i915 wmi snd_timer snd shpchp dw_dmac battery video elan_i2c dell_rbtn rfkill i2c_i801 dw_dmac_core snd_soc_sst_acpi mei_me mei snd_soc_sst_match lpc_ich drm_kms_helper
[ 5551.015186] soundcore i2c_smbus acpi_pad ac button drm i2c_algo_bit tpm_tis tpm_tis_core tpm i2c_designware_platform i2c_designware_core ip_tables x_tables autofs4 rtsx_usb_sdmmc rtsx_usb mfd_core ext4 crc16 usbhid jbd2 crc32c_generic fscrypto ecb mbcache sr_mod cdrom sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd ahci libahci psmouse xhci_pci xhci_hcd libata ehci_pci ehci_hcd scsi_mod r8169 mii usbcore usb_common fan thermal sdhci_acpi sdhci mmc_core fjes i2c_hid hid
[ 5551.015700] CPU: 0 PID: 838 Comm: wpa_supplicant Tainted: P O 4.8.0-kali1-amd64 #1 Debian 4.8.5-1kali1
[ 5551.015775] Hardware name: Dell Inc. Inspiron 3543/0MGXC6, BIOS A00 10/25/2014
[ 5551.015832] task: ffff906d98270080 task.stack: ffff906d934a4000
[ 5551.015874] RIP: 0010:[<ffffffffc0df441a>] [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.015974] RSP: 0018:ffff906d934a7ca8 EFLAGS: 00010297
[ 5551.016016] RAX: 0000000000000000 RBX: 00007fff13453d00 RCX: 0000000000000000
[ 5551.016067] RDX: 0000000000005013 RSI: 0000000000000000 RDI: ffffc64740b25000
[ 5551.016119] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 5551.016169] R10: 0000000000000036 R11: ffffffffc0df4390 R12: ffffc64740b25000
[ 5551.016224] R13: ffff906d0ca3d000 R14: ffffffff8429a888 R15: ffffffffc0df4390
[ 5551.016275] FS: 00007f275db5a880(0000) GS:ffff906d9ec00000(0000) knlGS:0000000000000000
[ 5551.016338] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5551.016382] CR2: 00007fff13453d00 CR3: 0000000116c12000 CR4: 00000000003406f0
[ 5551.016437] Stack:
[ 5551.016456] ffff906cacae6a00 ffff906d941d1000 ffff906d93dbd900 0000000000000024
[ 5551.016522] 000000005485238f ffff906d2a0b0540 ffff906d934a7e20 0000000000000000
[ 5551.016586] 0000000000008b36 ffffffff841ce8b8 ffff906d0ca3d000 00007fff13453d00
[ 5551.016652] Call Trace:
[ 5551.016681] [<ffffffff841ce8b8>] ? ioctl_standard_iw_point+0x2e8/0x3c0
[ 5551.016734] [<ffffffff841cea3a>] ? ioctl_standard_call+0xaa/0xd0
[ 5551.016783] [<ffffffff841cec55>] ? wext_handle_ioctl+0x75/0xd0
[ 5551.016828] [<ffffffff840fa62f>] ? dev_ioctl+0x29f/0x580
[ 5551.016871] [<ffffffff840bf8bd>] ? sock_ioctl+0x11d/0x280
[ 5551.016916] [<ffffffff83e1334f>] ? do_vfs_ioctl+0x9f/0x5f0
[ 5551.016962] [<ffffffff83dff6d0>] ? vfs_read+0x90/0x130
[ 5551.017006] [<ffffffff83e13914>] ? SyS_ioctl+0x74/0x80
[ 5551.017047] [<ffffffff841e18f6>] ? system_call_fast_compare_end+0xc/0x96
[ 5551.017100] Code: 00 bd 9c ff ff ff eb 78 48 85 db 0f 84 a0 00 00 00 48 83 3d 40 23 04 00 02 89 c5 76 0e 48 83 3d 5c a5 06 00 00 0f 84 a5 00 00 00 <8b> 03 83 f8 03 74 6b 83 f8 02 74 70 83 f8 01 0f 94 c0 0f b6 c0
[ 5551.017394] RIP [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.017477] RSP <ffff906d934a7ca8>
[ 5551.017504] CR2: 00007fff13453d00
[ 5551.027427] ---[ end trace 59de0c89298499a0 ]---
답변1
이 작업은 기존 노트북(RT5390이 포함된 HP g6)에서 수행해야 했습니다.
한때 입력했지만 필수는 아닌 ssid를 포함하여 많은 필드가 비어 있습니다.
가장 중요한 것은 사전 빌드를 위해 편집해야 하는 몇 가지 파일이 있다는 것입니다.
확인하기 위해 오래된 노트북을 부팅했습니다... tar를 다시 추출하고 병합했습니다...
구성 파일
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n
changed to:
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
pci_main_dev.c
일부 차단 논리를 주석 처리했습니다.
SET_NETDEV_DEV(net_dev,&(pci-dev->dev))
(네트워크 관리자는 그것 없이는 지원되지 않지만 로직은 커널 2.6.0용입니다. 실제로 그 커널에 이전 커널이 있었는지 기억이 나지 않습니다... 어느 시점에서 그렇게 했을 수도 있습니다).
rt_linux.c
skb->tail을 편집하여 unsigned int 32비트로 변환했습니다.
마지막으로 makefile에서:
- 주변 로직을 제거하고 ;chipset=5390으로 변경했습니다.
- 모든 PC 플랫폼을 제거했습니다.
- MAKE MAKE = make에 관한 모든 논리를 제거했습니다.
(지금은 더 나은 버전이 있다고 생각하기 때문에 이 단계를 모두 수행할 필요는 없지만 거기에 있습니다...)
dat 파일과 관련하여 3x 값을 변경했습니다(그러나 나중에 했던 것처럼 네트워크 관리자용으로 컴파일하는 경우에는 필요하지 않습니다).
- SSID=
- EncrypType=wpa-psk
- WPAPSK=
모든 빌드가 완료된 후 dat 파일을 넣습니다.
/etc/Wireless/RT5390STA/RT5390STA.dat
/etc/Wireless/RT5390STA/RT5390STACard.dat
원하시거나 도움이 되신다면 비교를 위해 .dat 파일을 복사해 드릴 수 있습니다.
업데이트: 블랙리스트에 사용할 모듈을 찾으세요.
sudo lscpi -v | less
현재 컴퓨터의 출력 예
03:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
DeviceName: SP1
Subsystem: Intel Corporation Dual Band Wireless AC 3165
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at f1000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number dc-53-60-ff-ff-5f-cb-f2
Capabilities: [14c] Latency Tolerance Reporting
Capabilities: [154] L1 PM Substates
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
이 경우 /etc/modprobe.d/wifi.conf에 블랙리스트를 추가합니다.
blacklist iwlwifi
무선 장치에 다음이 표시될 때까지 이를 반복합니다.
Kernel driver in use: rt2800pci
고쳐 쓰다:
내 tp-link USB 어댑터를 찾아냈습니다(OP는 pci 장치가 아닌 USB를 정렬하려고 했습니다).
아직 USB 소스 코드를 컴파일하지 않았습니다. 이는 이미 사용 가능한 커널 및 펌웨어 blob에서만 작동합니다.
[ 25.502040] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 25.660113] usb 2-1: New USB device found, idVendor=148f, idProduct=5572
[ 25.660124] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 25.660129] usb 2-1: Product: 802.11 n WLAN
[ 25.660133] usb 2-1: Manufacturer: Ralink
[ 25.660136] usb 2-1: SerialNumber: 1.0
[ 25.827234] usb 2-1: reset high-speed USB device number 2 using xhci_hcd
[ 25.977689] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[ 26.088458] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 000f detected
[ 26.090545] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 26.092720] usbcore: registered new interface driver rt2800usb
[ 26.122102] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 26.122379] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
현재 커널 모듈은 다음과 같습니다.
$ lsmod | grep rt2
rt2800usb 28672 0
rt2x00usb 20480 1 rt2800usb
rt2800lib 81920 1 rt2800usb
rt2x00lib 45056 3 rt2800lib,rt2800usb,rt2x00usb
crc_ccitt 16384 1 rt2800lib
mac80211 569344 4 rt2800lib,iwlmvm,rt2x00lib,rt2x00usb
cfg80211 471040 4 iwlmvm,iwlwifi,rt2x00lib,mac80211
usbcore 208896 6 rt2800usb,rt2x00usb,ehci_hcd,xhci_pci,xhci_hcd,ehci_pci
펌웨어 Blob은 다음 패키지에서 제공됩니다.
firmware-misc-nonfree: /lib/firmware/rt2870.bin
OP가 원하는 경우 이 USB 장치를 사용하여 소스 패키지를 테스트할 수 있습니까?
답변2
이 패키지를 확인해 보세요:https://aur.archlinux.org/packages/mt7610u_wifi_sta/
소중한 정보를 얻으실 수 있으실 거라 믿습니다