☰

wpa_신청자의 악몽

tag-icon • tag-icon wlan
wpa_신청자의 악몽

나는 며칠 동안 WPA 신청자들을 만지작거렸고 마침내 Google에서 새로운 단서를 찾을 수 없는 지점에 이르렀습니다. 그래서 질문은: 방금 debian wheezy를 실행하는 데스크탑 컴퓨터에 새로운 tp-link tl-wn881nd pci-e wifi 카드를 설치했습니다. wlan0액세스 포인트에 연결되어 있다고 주장하고(정말입니까? 아래 참조) ifconfig내가 할당한 올바른 고정 IP 주소를 보고하지만 액세스 포인트에 핑을 보낼 수 없고 syslog핸드셰이크에 오류가 있다고 말합니다.

network-manager첫째, 상황을 엉망으로 만들 수 있는 내용을 읽었습니다 . 나는 이것이 나에게 문제가 되지 않는다고 확신합니다.

$ which NetworkManager
##### blank #####
$ dpkg -l | grep -i network-manager
rc network-manager           0.9.4.0-10    amd-64    network management framework (daemon and userspace tools)
ii network-manager-openvpn   0.9.4.0-1     amd-64    network management framework (OpenVPN plugin core)

내 컴퓨터 사양은 다음과 같습니다.

$ uname -a
Linux mypc 3.2.0-4-amd64 #1 SMP Debian 3.2.60-1+deb7u3 x86_64 GNU/Linux
$ sudo dmidecode | grep -iA3 '^system information'
System Information
    Manufacturer: Dell Inc.                
    Product Name: OptiPlex 745                 
    Version: Not Specified

무선 네트워크 카드 사양은 다음과 같습니다.

$ lspci | grep -i wireless
02:00.0 Network controller: Atheros Communications Inc. AR9287 Wireless Network Adapter (PCI-Express) (rev 01)

Wi-Fi 카드가 활성화되어 있는지 확인했습니다.

$ sudo ip link set wlan0 up
$ sudo ip link show wlan0
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisk mq state DORMANT mode DORMANT qlen 1000
    link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff

카드가 내 ssid를 찾을 수 있습니다.

$ sudo iw wlan0 scan
BSS xx:xx:xx:xx:xx:xx (on wlan0) -- associated
    TSF: 2639667559 ysec (0d, 00:43:59)
    freq:2412
    beacon interval: 100
    capability: ESS Privacy ShortSlotTime (0x0411)
    signal: -56.00 dBm
    last seen: 692 ms ago
    Information elements from Probe Response frame:
    SSID: aphanumeric_with_underscores
    Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
    DS Parameter set: channel 1
    ERP: Use_Protection Barker_Preamble_Mode
    Extended supported rates: 6.0 12.0 24.0 48.0
    HT capabilities:
        Capabilities: 0x106e
            HT20/HT40
            SM Power Save disabled
            RX HT20 SGI
            RX HT40 SGI
            No RX STBC
            Max AMSDU length: 3839 bytes
            DSSS/CCK HT40
        Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
        Minimum RX AMPDU time spacing: 4 usec (0x05)
        HT RX MCS rate indexes supported: 0-7, 32
        HT TX MCS rate indexes are undefined
    HT operation:
        * primary channel: 1
        * secondary channel offset: no secondary
        * STA channel width 20MHz
        * RIFS: 0
        * HT protection: non-HT mixed
        * non-GF present: 1
        * OBSS non-GF present: 0
        * dual beacon: 0
        * dual CTS protection: 0
        * STBC beacon: 0
        * L-SIG TXOP Prot: 0
        * PCO active: 0
        * PCO phase: 0
    RSN:* Version: 1
        * Group cipher: CCMP
        * Pairwise ciphers: CCMP
        * Authentication suites: PSK
        * Capabilities: (0x0000)
    WMM:* Parameter version 1
        * BE: CW 15-1023, AIFSN 3
        * BK: CW 15-1023, AIFSN 7
        * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
        * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
    Extended capabilities: HT Information Exchange Supported
    Country: AL Environment: Indoor/Outdoor
        Channels [1 - 13] @ 15 dBm

나어딘가에서 읽어보세요wpa_supplicant 옵션을 에 넣을 수 있으므로 /etc/network/interfaces여기에 내 것이 있습니다.

$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

# don't use `auto wlan0` since this will infinitely try to connect at
# boot time, and i will have to remove the hard drive, mount it on
# another pc and remove `auto wlan0` from this file just to get a
# command prompt again!
iface wlan0 inet static
    wpa-ssid "aphanumeric_with_underscores"
    wpa-psk "my wpa2 password"
    wpa-ap-scan 1
    wpa-proto WPA2
    wpa-pairwise CCMP
    wpa-group CCMP
    wpa-key-mgmt WPA-PSK
    address 192.168.1.50
    netmask 255.255.255.0
    gateway 192.168.1.1
    dns-nameservers 8.8.8.8 8.8.4.4

현재 파일이 없다는 점에 유의하세요 wpa_supplicant.conf.

$ ls /etc/wpa_supplicant.conf
ls: cannot access /etc/wpa_supplicant.conf: No such file or directory
$ ls /etc/wpa_supplicant/*
action_wpa.sh  functions.sh  ifupdown.sh

wlan0이제 인터페이스를 다시 시작하면 다음과 같습니다 .

$ sudo ifdown wlan0
$ sudo ifup wlan0

IP 주소가 올바르게 할당되었습니다.

$ ifconfig
lo       ...

wlan0    Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx
         inet addr 192.168.1.50  Bcast:192.168.1.255  Mask:255.255.255.0
         inet6 addr: fe80::16cc:20ff:feea:4578/64 Scope:Link
         UP BROADCAST MULTICAST  NTU:1500  Metric:1
         RX packets:3075 errors:0 dropped:0 overruns:0 frame:0
         TX packets:4028 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:347475 (339.3KiB)  TX bytes:586219 (572.4KiB)

하지만 문제는 wlan0인터페이스가 작동하는 것 같지만 인터넷에 액세스할 수 없거나 액세스 포인트에 핑을 보낼 수도 없다는 것입니다.

$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
From 192.168.1.50 icmp_seq=2 Destination Host Unreachable
From 192.168.1.50 icmp_seq=3 Destination Host Unreachable
^C
--- 192.168.1.1 ping statistics ---
3 packets transmitted, 0 received, +2 errors, 100% packet loss, time 2015ms

살펴보면 /var/log/syslog다음과 같은 불쾌한 오류가 표시됩니다.

Mar 18 01:23:11 mypc kernel: [  148.242137] wlan0: authenticate with xx.xx.xx.xx.xx.xx (try 1)
Mar 18 01:23:11 mypc kernel: [  148.244009] wlan0: authenticated
Mar 18 01:23:11 mypc kernel: [  148.265967] wlan0: associate with xx.xx.xx.xx.xx.xx (try 1)
Mar 18 01:23:11 mypc kernel: [  148.287770] wlan0: RX AssocResp from xx.xx.xx.xx.xx.xx (capab=0x411 status=0 aid=1)
Mar 18 01:23:11 mypc kernel: [  148.287774] wlan0: associated
Mar 18 01:23:11 mypc kernel: [  148.287774] wlan0: associated
Mar 18 01:23:11 mypc wpa_supplicant[4473]: wlan0: Associated with xx.xx.xx.xx.xx.xx
Mar 18 01:23:11 mypc kernel: [  148.297421] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mar 18 01:23:11 mypc kernel: [  148.297651] cfg80211: Calling CRDA for country AL
Mar 18 01:23:11 mypc kernel: [  148.303008] cfg80211: Regulatory domain changed to country: AL
Mar 18 01:23:11 mypc kernel: [  148.303013] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mar 18 01:23:11 mypc kernel: [  148.303018] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Mar 18 01:23:11 mypc kernel: [  148.303022] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 01:23:11 mypc kernel: [  148.303026] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 01:23:11 mypc kernel: [  148.303029] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
Mar 18 01:23:19 mypc kernel: [  155.819739] wlan0: deauthenticated from xx:xx:xx:xx:xx:xx (Reason: 15)
Mar 18 01:23:19 mypc wpa_supplicant[4473]: wlan0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
Mar 18 01:23:19 mypc wpa_supplicant[4473]: wlan0: CTRL-EVENT-DISCONNECTED bssid=xx:xx:xx:xx:xx:xx reason=15

이 문제를 해결하고 액세스 포인트를 핑하는 방법을 아는 사람이 있습니까 wlan0?

편집 1: 고정 IP 대신 DHCP를 사용해 보세요.

나는 /etc/network/interfaces이것을 다음과 같이 바꾼다:

$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

# don't use `auto wlan0` since this will infinitely try to connect at
# boot time, and i will have to remove the hard drive, mount it on
# another pc and remove `auto wlan0` from this file just to get a
# command prompt again!
iface wlan0 inet dhcp
    wpa-ssid "aphanumeric_with_underscores"
    wpa-psk "my wpa2 password"
    wpa-ap-scan 1
    wpa-proto WPA2
    wpa-pairwise CCMP
    wpa-group CCMP
    wpa-key-mgmt WPA-PSK

( wpa_supplicant.conf수정 1에는 여전히 존재하지 않습니다.) 이제 인터페이스를 시작하면 명령줄에 몇 가지 새로운 오류가 발생합니다.

$ sudo ifup wlan0
Operation failed.
Failed to bring up wlan0

시스템 로그에는 이전과 동일한 실패 메시지가 계속해서 표시됩니다.

Mar 18 08:59:01 mypc kernel: [ 2493.163777] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Mar 18 08:59:02 mypc wpa_supplicant[6151]: wlan0: SME: Trying to authenticate with xx:xx:xx:xx:xx:xx (SSID='alphanumeric_with_underscores' freq=2412 MHz)
Mar 18 08:59:02 mypc kernel: [ 2493.974111] wlan0: authenticate with xx:xx:xx:xx:xx:xx (try 1)
Mar 18 08:59:02 mypc kernel: [ 2493.976083] wlan0: authenticated         
Mar 18 08:59:02 mypc wpa_supplicant[6151]: wlan0: Trying to associate with xx:xx:xx:xx:xx:xx (SSID='aphanumeric_with_underscores' freq=2412 MHz)
Mar 18 08:59:02 mypc kernel: [ 2493.998016] wlan0: associate with xx:xx:xx:xx:xx:xx (try 1)
Mar 18 08:59:02 mypc kernel: [ 2494.019518] wlan0: RX ReassocResp from xx:xx:xx:xx:xx:xx (capab=0x411 status=0 aid=2)
Mar 18 08:59:02 mypc kernel: [ 2494.019523] wlan0: associated            
Mar 18 08:59:02 mypc wpa_supplicant[6151]: wlan0: Associated with xx:xx:xx:xx:xx:xx
Mar 18 08:59:02 mypc kernel: [ 2494.028721] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mar 18 08:59:02 mypc kernel: [ 2494.028873] cfg80211: Calling CRDA for country: AL
Mar 18 08:59:02 mypc kernel: [ 2494.033830] cfg80211: Regulatory domain changed to country: AL
Mar 18 08:59:02 mypc kernel: [ 2494.033835] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mar 18 08:59:02 mypc kernel: [ 2494.033839] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:02 mypc kernel: [ 2494.033843] cfg80211:     (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:02 mypc kernel: [ 2494.033846] cfg80211:     (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:02 mypc kernel: [ 2494.033849] cfg80211:     (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.499716] wlan0: deauthenticated from xx:xx:xx:xx:xx:xx (Reason: 15)
Mar 18 08:59:09 mypc wpa_supplicant[6151]: wlan0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
Mar 18 08:59:09 mypc wpa_supplicant[6151]: wlan0: CTRL-EVENT-DISCONNECTED bssid=xx:xx:xx:xx:xx:xx reason=15
Mar 18 08:59:09 mypc kernel: [ 2501.536289] cfg80211: Calling CRDA to update world regulatory domain
Mar 18 08:59:09 mypc kernel: [ 2501.541764] cfg80211: World regulatory domain updated:
Mar 18 08:59:09 mypc kernel: [ 2501.541770] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mar 18 08:59:09 mypc kernel: [ 2501.541775] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.541779] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.541782] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.541786] cfg80211:     (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.541790] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 08:59:09 mypc kernel: [ 2501.541794] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
Mar 18 08:59:10 mypc wpa_supplicant[6151]: wlan0: SME: Trying to authenticate with xx:xx:xx:xx:xx:xx (SSID='aphanumeric_with_underscores' freq=2412 MHz)
Mar 18 08:59:10 mypc kernel: [ 2502.434112] wlan0: authenticate with xx:xx:xx:xx:xx:xx (try 1)
Mar 18 08:59:10 mypc kernel: [ 2502.436071] wlan0: authenticated
etc

eth0은 dhcp와 잘 작동하므로 dhcp 자체에는 문제가 없습니다.

편집 2: wpa_passphrase에서 psk 해시를 사용해 보세요.

$ wpa_passphrase myssid mypassword
network={
    ssid="myssid"
    #psk="mypassword"
    psk=xxxxxxxxxxxx...
}

이 새로운 psk를 다음에서 사용하세요 /etc/network/interfaces:

$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

# don't use `auto wlan0` since this will infinitely try to connect at
# boot time, and i will have to remove the hard drive, mount it on
# another pc and remove `auto wlan0` from this file just to get a
# command prompt again!
iface wlan0 inet dhcp
    wpa-ssid "aphanumeric_with_underscores"
    wpa-psk xxxxxxxxxxxxxxxx
    wpa-ap-scan 1
    wpa-proto WPA2
    wpa-pairwise CCMP
    wpa-group CCMP
    wpa-key-mgmt WPA-PSK

다시 시도하십시오:

$ sudo iplink set wlan0 down
$ sudo iplink set wlan0 up
$ sudo ifup wlan0
cat: /var/run/wpa_supplicant.wlan0.pid: No such file or directory
Operation failed.
Failed to bring up wlan0.

글쎄요, 그건 재미있는 실수였어요. 조사:

$ sudo su
# cd /var/run/wpa_supplicant/
# ls -l
total 0
srwxrwx--- 1 root root 0 Mar 18 09:26 wlan0
# cat wlan0 
cat: wlan0: No such device or address

/var/log/syslog하지만 여전히 같은 오류가 표시됩니다.

수정 3: 매우 기본적인 ssid 및 비밀번호 설정

ssid를 abc다음과 같이 설정했습니다 abcdefgh.

$ wpa_passphrase abc abcdefgh
network={
    ssid="abc"
    #psk="abcdefgh"
    psk=ba89407e92b8efec11c227e3cce9f25c8dcc4b3651fe2be02d91d9ebda96e913
}

그런데 어떤 사전 공유 키를 입력해도 결과는 수정 1, 수정 2와 같습니다./etc/network/interfaces

$ sudo ip link set wlan0 down                                                   
$ sudo ip link set wlan0 up                                                     
$ sudo ip link show wlan0                                                       
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state DORMANT mode DEFAULT qlen 1000
    link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff                          
$ sudo ifdown wlan0                                                             
ifdown: interface wlan0 not configured                                          
$ sudo rm /var/run/wpa_supplicant/wlan0                                         
$ sudo ifup wlan0                                                               
wpa_supplicant: ctrl_interface socket not found at /var/run/wpa_supplicant/wlan0
run-parts: /etc/network/if-pre-up.d/wpasupplicant exited with return code 1     
Operation failed.                                                               
Failed to bring up wlan0.

수정 사항 4: 명령줄 디버그 모드에서 wpa_supplicant 사용

다음에서 모든 WPA 설정을 제거합니다 /etc/network/interfaces.

$ cat /etc/network/interfaces
auto lo
iface lo inet loopback
iface wlan0 inet dhcp

이제 wpa_supplicant.conf파일을 만듭니다.

$ sudo sh -c 'wpa_passphrase abc abcdefgh > /etc/wpa_supplicant/wpa_supplicant.conf'

다음 정보를 포함하도록 파일을 편집합니다.

ap_scan=1
ctrl_interface=DIR=/var/run/wpa_supplicant
ctrl_interface_group=0
network={
    proto=WPA2
    pairwise=CCMP
    group=CCMP
    key_mgmt=WPA-PSK
    ssid="abc"
    #psk="abcdefgh"
    psk=ba89407e92b8efec11c227e3cce9f25c8dcc4b3651fe2be02d91d9ebda96e913
}

직접 실행 wpa_supplicant:

$ sudo ip link show wlan0
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN mode DEFAULT qlen 1000
    link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff
$ sudo ip link set wlan0 up
$ sudo wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
wlan0: Trying to associate with xx:xx:xx:xx:xx:xx (SSID='abc' freq=2412 MHz)
wlan0: Associated with 00:00:00:00:00:00
wlan0: CTRL-EVENT-DISCONNECTED bssid=xx:xx:xx:xx:xx:xx reason=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
wlan0: Trying to associate with xx:xx:xx:xx:xx:xx (SSID='abc' freq=2412 MHz)
wlan0: Associated with 00:00:00:00:00:00
wlan0: CTRL-EVENT-DISCONNECTED bssid=xx:xx:xx:xx:xx:xx reason=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWSCAN]: Device or resource busy
wlan0: Failed to initiate AP scan
wlan0: Trying to associate with xx:xx:xx:xx:xx:xx (SSID='abc' freq=2412 MHz)
wlan0: Associated with 00:00:00:00:00:00
wlan0: CTRL-EVENT-DISCONNECTED bssid=xx:xx:xx:xx:xx:xx reason=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
^Cwlan0: CTRL-EVENT-TERMINATING - signal 2 received

다시 한 번 좀 더 자세한 디버깅을 해보겠습니다.

$ sudo wpa_supplicant -d -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf -f /tmp/wpa_supplicant.tl-wn881nd.errors

출력 보기여기.

ioctl[SIOCSIWENCODEEXT]: Invalid argumentWi-Fi 카드와 커널이 호환되지 않는 것 같은데요 ?그렇다면 이 문제를 어떻게 진단하고 해결합니까?

답변1

빌어먹을 Wi-Fi 카드가 PCI-Express 슬롯에 올바르게 연결되지 않았습니다! 꺼내서 슬롯에 붙은 먼지를 불어내고 이번에는 세게 밀어 넣었습니다. 이제 모든 것이 잘 작동합니다.

# the wifi led is not lit up on the outside of the pc case

$ sudo ip link show wlan0
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000
    link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff
$ sudo ip link set wlan0 up

# now the wifi led is lit up on the outside of the pc case

$ sudo ip link show wlan0
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT qlen 1000
    link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff
$ sudo wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
wlan0: Trying to associate with 00:60:64:4c:37:fc (SSID='abc' freq=2412 MHz)
wlan0: Associated with 00:60:64:4c:37:fc
wlan0: WPA: Key negotiation completed with 00:60:64:4c:37:fc [PTK=CCMP GTK=CCMP]
wlan0: CTRL-EVENT-CONNECTED - Connection to 00:60:64:4c:37:fc completed (auth) [id=0 id_str=]
wlan0: CTRL-EVENT-DISCONNECTED bssid=00:60:64:4c:37:fc reason=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
ioctl[SIOCSIWENCODEEXT]: Invalid argument
wlan0: Trying to associate with 00:60:64:4c:37:fc (SSID='abc' freq=2412 MHz)
wlan0: Associated with 00:60:64:4c:37:fc
wlan0: WPA: Key negotiation completed with 00:60:64:4c:37:fc [PTK=CCMP GTK=CCMP]
wlan0: CTRL-EVENT-CONNECTED - Connection to 00:60:64:4c:37:fc completed (reauth) [id=0 id_str=]
$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_req=1 ttl=254 time=0.510 ms
64 bytes from 192.168.1.1: icmp_req=2 ttl=254 time=0.578 ms
^C
--- 192.168.1.1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 999ms
rtt min/avg/max/mdev = 0.510/0.544/0.578/0.034 ms

올바른 것은 /var/log/syslog다음과 같습니다.

Mar 18 13:38:19 mypc kernel: [  542.538613] wlan0: authenticate with 00:60:64:4c:37:fc (try 1)
Mar 18 13:38:19 mypc kernel: [  542.540517] wlan0: authenticated         
Mar 18 13:38:19 mypc kernel: [  542.540553] wlan0: associate with 00:60:64:4c:37:fc (try 1)
Mar 18 13:38:19 mypc kernel: [  542.563331] wlan0: RX AssocResp from 00:60:64:4c:37:fc (capab=0x411 status=0 aid=3)
Mar 18 13:38:19 mypc kernel: [  542.563336] wlan0: associated            
Mar 18 13:38:19 mypc kernel: [  542.573034] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Mar 18 13:38:19 mypc kernel: [  542.573220] cfg80211: Calling CRDA for country: AL
Mar 18 13:38:19 mypc kernel: [  542.578955] cfg80211: Regulatory domain changed to country: AL
Mar 18 13:38:19 mypc kernel: [  542.578960] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mar 18 13:38:19 mypc kernel: [  542.578965] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Mar 18 13:38:19 mypc kernel: [  542.578969] cfg80211:     (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 13:38:19 mypc kernel: [  542.578972] cfg80211:     (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Mar 18 13:38:19 mypc kernel: [  542.578976] cfg80211:     (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)

이 줄은 한 번만 나타나며 더 이상 반복되지 않습니다.syslog

:)

wpa_supplicant.conf파일을 삭제하고 모든 내용을 파일에 넣으면 이제 잘 작동합니다 /etc/network/interfaces.

$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

# don't use `auto wlan0` since this will infinitely try to connect at
# boot time, and i will have to remove the hard drive, mount it on
# another pc and remove `auto wlan0` from this file just to get a
# command prompt again!
iface wlan0 inet static
    wpa-ssid "aphanumeric_with_underscores"

    # both the plaintext password and the ascii-hex hash from
    # wpa_passphrase work fine for me here:
    wpa-psk "my wpa2 password"

    wpa-ap-scan 1
    wpa-proto WPA2
    wpa-pairwise CCMP
    wpa-group CCMP
    wpa-key-mgmt WPA-PSK
    address 192.168.1.50
    netmask 255.255.255.0
    gateway 192.168.1.1
    dns-nameservers 8.8.8.8 8.8.4.4
and note that there is currently no wpa_supplicant.conf file:

$ ls /etc/wpa_supplicant.conf
ls: cannot access /etc/wpa_supplicant.conf: No such file or directory
$ ls /etc/wpa_supplicant/*
action_wpa.sh  functions.sh  ifupdown.sh

답변2

다음을 기반으로 wpa_supplicant를 사용해 보겠습니다.우분투 사용자 위키. 즉, 모든 wpa 콘텐츠를 넣고 /etc/wpa_supplicant/wpa_supplicant.conf다음 내용 /etc/network/interfaces만 포함하도록 수정합니다.

...
auto wlan0
iface wlan0 inet dhcp
    wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
...

추가로 wpa_supplicant( wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -d)를 수동으로 시작합니다. wpa_supplicant에 문제가 있으면 표시되어야 합니다.

편집: @casey의 의견에 추가로 동의합니다. 키에 일부 오류가 있을 수 있습니다.

관련 정보