내 컴퓨터에 이상한 문제가 있어서 어떻게 해야 할지 모르겠습니다. 모든 것은 특정 문자(산스크리트어 문자)가 내 Emacs에 더 이상 표시될 수 없을 때 시작되었습니다. 이러한 문자가 포함된 문서를 열고 해당 문자가 나타나야 하는 위치로 스크롤할 때마다 Emacs는 자동으로 닫힙니다.
그러다가 리눅스 민트 시스템 보고서에 오류가 기록되고, 호출하려고 하면 프로그램도 종료됩니다. 나는 가능한 모든 것을 시도했습니다. 이는 내 Emacs 구성으로 인한 것이 아닙니다.
Firefox나 Thunderbird도 때때로 충돌을 일으킬 수 있습니다. 하지만 그 원인이 정확히 무엇인지는 모르겠습니다.
새 RAM을 구입했는데 RAM에서도 이 문제가 발생하지 않았습니다.
해당 충돌 보고서에 액세스하는 방법을 알아냈습니다( dmesg).
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437715] ata2.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x0
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437722] ata2.00: irq_stat 0x40000008
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437726] ata2.00: failed command: READ FPDMA QUEUED
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437733] ata2.00: cmd 60/08:38:58:01:17/00:00:00:00:00/40 tag 7 ncq dma 4096 in
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437733] res 41/40:00:58:01:17/00:00:00:00:00/00 Emask 0x409 (media error) <F>
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437736] ata2.00: status: { DRDY ERR }
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.437739] ata2.00: error: { UNC }
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443486] ata2.00: configured for UDMA/133
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443504] sd 1:0:0:0: [sdb] tag#7 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443507] sd 1:0:0:0: [sdb] tag#7 Sense Key : Medium Error [current]
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443509] sd 1:0:0:0: [sdb] tag#7 Add. Sense: Unrecovered read error - auto reallocate failed
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443512] sd 1:0:0:0: [sdb] tag#7 CDB: Read(10) 28 00 00 17 01 58 00 00 08 00
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443515] blk_update_request: I/O error, dev sdb, sector 1507672 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.443540] ata2: EH complete
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485670] ata2.00: exception Emask 0x0 SAct 0x1000 SErr 0x0 action 0x0
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485675] ata2.00: irq_stat 0x40000008
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485679] ata2.00: failed command: READ FPDMA QUEUED
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485684] ata2.00: cmd 60/08:60:58:01:17/00:00:00:00:00/40 tag 12 ncq dma 4096 in
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485684] res 41/40:00:58:01:17/00:00:00:00:00/00 Emask 0x409 (media error) <F>
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485687] ata2.00: status: { DRDY ERR }
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.485689] ata2.00: error: { UNC }
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491673] ata2.00: configured for UDMA/133
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491691] sd 1:0:0:0: [sdb] tag#12 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491696] sd 1:0:0:0: [sdb] tag#12 Sense Key : Medium Error [current]
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491699] sd 1:0:0:0: [sdb] tag#12 Add. Sense: Unrecovered read error - auto reallocate failed
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491703] sd 1:0:0:0: [sdb] tag#12 CDB: Read(10) 28 00 00 17 01 58 00 00 08 00
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491707] blk_update_request: I/O error, dev sdb, sector 1507672 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
Apr 9 17:29:01 enjotel-mint20 kernel: [ 1272.491739] ata2: EH complete
Apr 9 17:29:01 enjotel-mint20 systemd[1]: Started Process Core Dump (PID 6655/UID 0).
Apr 9 17:29:02 enjotel-mint20 systemd-coredump[6656]: Process 6620 (emacs28) of user 1000 dumped core.#012#012Stack trace of thread 6620:#012#0 0x00007f4758af12ab raise (libpthread.so.0 + 0x142ab)#012#1 0x0000000000426a3d n/a (emacs-28.128 + 0x26a3d)#012#2 0x0000000000426efc n/a (emacs-28.128 + 0x26efc)#012#3 0x000000000052eecd n/a (emacs-28.128 + 0x12eecd)#012#4 0x000000000052efbf n/a (emacs-28.128 + 0x12efbf)#012#5 0x00007f4758af1420 __restore_rt (libpthread.so.0 + 0x14420)#012#6 0x00007f4758d280f0 n/a (libotf.so.0 + 0xb0f0)#012#7 0x00007f4758d2a013 OTF_get_features (libotf.so.0 + 0xd013)#012#8 0x00007f4758d2a078 OTF_check_features (libotf.so.0 + 0xd078)#012#9 0x000000000060ba72 n/a (emacs-28.128 + 0x20ba72)#012#10 0x00000000005af03c n/a (emacs-28.128 + 0x1af03c)#012#11 0x00000000005af9d8 n/a (emacs-28.128 + 0x1af9d8)#012#12 0x0000000000610859 n/a (emacs-28.128 + 0x210859)#012#13 0x00000000006110db n/a (emacs-28.128 + 0x2110db)#012#14 0x00000000006115f9 n/a (emacs-28.128 + 0x2115f9)#012#15 0x00000000005ae249 n/a (emacs-28.128 + 0x1ae249)#012#16 0x00000000005fa4be n/a (emacs-28.128 + 0x1fa4be)#012#17 0x00000000005fc793 n/a (emacs-28.128 + 0x1fc793)#012#18 0x00000000005fd518 n/a (emacs-28.128 + 0x1fd518)#012#19 0x00000000005268cd n/a (emacs-28.128 + 0x1268cd)#012#20 0x00000000005942e7 n/a (emacs-28.128 + 0x1942e7)#012#21 0x000000000051650a n/a (emacs-28.128 + 0x11650a)#012#22 0x0000000000594229 n/a (emacs-28.128 + 0x194229)#012#23 0x00000000005164a6 n/a (emacs-28.128 + 0x1164a6)#012#24 0x000000000051be50 n/a (emacs-28.128 + 0x11be50)#012#25 0x000000000051c1a6 n/a (emacs-28.128 + 0x11c1a6)#012#26 0x000000000042e465 n/a (emacs-28.128 + 0x2e465)#012#27 0x00007f4758751083 __libc_start_main (libc.so.6 + 0x24083)#012#28 0x000000000042eb3e n/a (emacs-28.128 + 0x2eb3e)#012#012Stack trace of thread 6623:#012#0 0x00007f475883fbbf __GI___poll (libc.so.6 + 0x112bbf)#012#1 0x00007f475fa0f36e n/a (libglib-2.0.so.0 + 0x5236e)#012#2 0x00007f475fa0f4a3 g_main_context_iteration (libglib-2.0.so.0 + 0x524a3)#012#3 0x00007f475fa0f4f1 n/a (libglib-2.0.so.0 + 0x524f1)#012#4 0x00007f475fa38ae1 n/a (libglib-2.0.so.0 + 0x7bae1)#012#5 0x00007f4758ae5609 start_thread (libpthread.so.0 + 0x8609)#012#6 0x00007f475884c353 __clone (libc.so.6 + 0x11f353)#012#012Stack trace of thread 6624:#012#0 0x00007f475883fbbf __GI___poll (libc.so.6 + 0x112bbf)#012#1 0x00007f475fa0f36e n/a (libglib-2.0.so.0 + 0x5236e)#012#2 0x00007f475fa0f6f3 g_main_loop_run (libglib-2.0.so.0 + 0x526f3)#012#3 0x00007f475fc6bf8a n/a (libgio-2.0.so.0 + 0x11ef8a)#012#4 0x00007f475fa38ae1 n/a (libglib-2.0.so.0 + 0x7bae1)#012#5 0x00007f4758ae5609 start_thread (libpthread.so.0 + 0x8609)#012#6 0x00007f475884c353 __clone (libc.so.6 + 0x11f353)#012#012Stack trace of thread 6625:#012#0 0x00007f475883fbbf __GI___poll (libc.so.6 + 0x112bbf)#012#1 0x00007f475fa0f36e n/a (libglib-2.0.so.0 + 0x5236e)#012#2 0x00007f475fa0f4a3 g_main_context_iteration (libglib-2.0.so.0 + 0x524a3)#012#3 0x00007f47528ef99d n/a (libdconfsettings.so + 0xa99d)#012#4 0x00007f475fa38ae1 n/a (libglib-2.0.so.0 + 0x7bae1)#012#5 0x00007f4758ae5609 start_thread (libpthread.so.0 + 0x8609)#012#6 0x00007f475884c353 __clone (libc.so.6 + 0x11f353)
Apr 9 17:29:02 enjotel-mint20 systemd[1]: [email protected]: Succeeded.
enjotel@enjotel-mint20:~$에 대한 결과는 다음과 같습니다 sudo smartctl -x /dev/sdb.
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-176-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Marvell based SanDisk SSDs
Device Model: SanDisk SSD PLUS 1000GB
Serial Number: 20504Z800982
LU WWN Device Id: 5 001b44 8be8fa562
Firmware Version: UH5100RL
User Capacity: 1.000.207.286.272 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Apr 9 18:35:18 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x15) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 182) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0
9 Power_On_Hours -O--CK 100 100 000 - 9891
12 Power_Cycle_Count -O--CK 100 100 000 - 1411
165 Total_Write/Erase_Count -O--CK 100 100 000 - 1774
166 Min_W/E_Cycle -O--CK 100 100 --- - 5
167 Min_Bad_Block/Die -O--CK 100 100 --- - 0
168 Maximum_Erase_Cycle -O--CK 100 100 --- - 26
169 Total_Bad_Block -O--CK 100 100 --- - 1501
170 Unknown_Attribute -O--CK 100 100 --- - 0
171 Program_Fail_Count -O--CK 100 100 000 - 0
172 Erase_Fail_Count -O--CK 100 100 000 - 0
173 Avg_Write/Erase_Count -O--CK 100 100 000 - 5
174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 20
184 End-to-End_Error -O--CK 100 100 --- - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 11155
188 Command_Timeout -O--CK 100 100 --- - 0
194 Temperature_Celsius -O---K 073 054 000 - 27 (Min/Max 2/54)
199 SATA_CRC_Error -O--CK 100 100 --- - 0
230 Perc_Write/Erase_Count -O--CK 100 100 000 - 1286 256 1286
232 Perc_Avail_Resrvd_Space PO--CK 100 100 005 - 100
233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 5636
234 Perc_Write/Erase_Ct_BC -O--CK 100 100 000 - 27722
241 Total_Writes_GiB ----CK 100 100 000 - 11337
242 Total_Reads_GiB ----CK 100 100 000 - 12756
244 Thermal_Throttle -O--CK 000 100 --- - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 16 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 1 Device vendor specific log
0xa2 GPL,SL VS 2 Device vendor specific log
0xa3-0xa4 GPL,SL VS 1 Device vendor specific log
0xa7 GPL,SL VS 1 Device vendor specific log
0xa9 GPL,SL VS 3 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (16 sectors) Device
Error Count: 11155 (device log contains only the most recent 64
errors) CR = Command Register FEATR = Features Register COUNT
= Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder
High) Register ] LBA LM = LBA Mid (was: Cylinder Low)
Register ] Register LL = LBA Low (was: Sector Number)
Register ] DV = Device (was: Device/Head) Register DC =
Device Control Register ER = Error register ST = Status
register Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and
sss=millisec. It "wraps" after 49.710 days.
Error 11155 [4] occurred at disk power-on lifetime: 9890 hours (412
days + 2 hours) When the command that caused the error occurred, the
device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40
-- 51 00 00 00 00 6b b4 7c 6c a0 00 Error: UNC
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 2f 00 00 00 01 00 00 00 00 08 30 a0 00 02:05:58.722 READ LOG EXT ea 00 00 00 00 00 00 00 00
00 00 a0 00 02:05:58.667 FLUSH CACHE EXT ea 00 00 00 00 00 00
00 00 00 00 a0 00 02:05:49.830 FLUSH CACHE EXT 2f 00 00 00 01
00 00 00 00 08 30 a0 00 02:05:28.826 READ LOG EXT 2f 00 00 00
01 00 00 00 00 08 30 a0 00 02:05:28.781 READ LOG EXT
Error 11154 [3] occurred at disk power-on lifetime: 9890 hours (412
days + 2 hours) When the command that caused the error occurred, the
device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40
-- 51 00 00 00 00 6b b4 7c 6c a0 00
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:05:58.667 FLUSH CACHE EXT ea 00 00 00 00 00 00 00
00 00 00 a0 00 02:05:49.830 FLUSH CACHE EXT 2f 00 00 00 01 00
00 00 00 08 30 a0 00 02:05:28.826 READ LOG EXT 2f 00 00 00 01
00 00 00 00 08 30 a0 00 02:05:28.781 READ LOG EXT 2f 00 00 00
01 00 00 00 00 08 30 a0 00 02:05:28.721 READ LOG EXT
Error 11153 [2] occurred at disk power-on lifetime: 9890 hours (412
days + 2 hours) When the command that caused the error occurred, the
device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40
-- 51 00 28 00 00 6b b4 7c 94 a0 00
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 00 02:05:49.830 FLUSH CACHE EXT 2f 00 00 00 01 00 00 00
00 08 30 a0 00 02:05:28.826 READ LOG EXT 2f 00 00 00 01 00 00
00 00 08 30 a0 00 02:05:28.781 READ LOG EXT 2f 00 00 00 01 00
00 00 00 08 30 a0 00 02:05:28.721 READ LOG EXT 2f 00 00 00 01
00 00 00 00 08 30 a0 00 02:05:28.666 READ LOG EXT
Error 11152 [1] occurred at disk power-on lifetime: 9890 hours (412
days + 2 hours) When the command that caused the error occurred, the
device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40
-- 51 00 00 00 00 6b b4 7c 6c a0 00 Error: UNC
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 2f 00 00 00 01 00 00 00 00 08 30 a0 00 02:05:28.826 READ LOG EXT 2f 00 00 00 01 00 00 00 00
08 30 a0 00 02:05:28.781 READ LOG EXT 2f 00 00 00 01 00 00 00
00 08 30 a0 00 02:05:28.721 READ LOG EXT 2f 00 00 00 01 00 00
00 00 08 30 a0 00 02:05:28.666 READ LOG EXT 2f 00 00 00 01 00
00 00 00 08 30 a0 00 02:05:28.621 READ LOG EXT
Error 11151 [0] occurred at disk power-on lifetime: 9890 hours (412
days + 2 hours) When the command that caused the error occurred, the
device was active or idle.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40
-- 51 00 00 00 00 6b b4 7c 6c a0 00 Error: UNC
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 2f 00 00 00 01 00 00 00 00 08 30 a0 00 02:05:28.781 READ LOG EXT 2f 00 00 00 01 00 00 00 00
08 30 a0 00 02:05:28.721 READ LOG EXT 2f 00 00 00 01 00 00 00
00 08 30 a0 00 02:05:28.666 READ LOG EXT 2f 00 00 00 01 00 00
00 00 08 30 a0 00 02:05:28.621 READ LOG EXT 2f 00 00 00 01 00
00 00 00 08 30 a0 00 02:05:28.566 READ LOG EXT
Warning! SMART Extended Comprehensive Error Log Structure error:
invalid SMART checksum. Error 11150 [63] occurred at disk power-on
lifetime: 61166 hours (2548 days + 14 hours) When the command that
caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00
-- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 45 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00
00 00 00 00 00 00 00 00 44 13d+06:08:44.612 NOP [Abort queued
commands] 00 00 00 00 00 00 00 00 00 00 00 00 43 9d+22:36:33.459
NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 42
6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00
00 00 00 00 41 3d+07:32:11.153 NOP [Abort queued commands]
Error 11149 [62] occurred at disk power-on lifetime: 61166 hours (2548
days + 14 hours) When the command that caused the error occurred,
the device was in an unknown state.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00
-- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 35 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00
00 00 00 00 00 00 00 00 34 13d+06:08:44.612 NOP [Abort queued
commands] 00 00 00 00 00 00 00 00 00 00 00 00 33 9d+22:36:33.459
NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 32
6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00
00 00 00 00 31 3d+07:32:11.153 NOP [Abort queued commands]
Error 11148 [61] occurred at disk power-on lifetime: 61166 hours (2548
days + 14 hours) When the command that caused the error occurred,
the device was in an unknown state.
After command completion occurred, registers were: ER -- ST COUNT
LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00
-- 00 00 00 00 00 00 00 00 00 00 00
Commands leading to the command that caused the error were: CR
FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time
Command/Feature_Name -- == -- == -- == == == -- -- -- -- --
--------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 00 25 16d+13:40:55.765 NOP [Abort queued commands] 00 00 00 00
00 00 00 00 00 00 00 00 24 13d+06:08:44.612 NOP [Abort queued
commands] 00 00 00 00 00 00 00 00 00 00 00 00 23 9d+22:36:33.459
NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 00 22
6d+15:04:22.306 NOP [Abort queued commands] 00 00 00 00 00 00 00 00
00 00 00 00 21 3d+07:32:11.153 NOP [Abort queued commands]
SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have
been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04) Page Offset Size Value Flags
Description 0x01 ===== = = === == General Statistics
(rev 1) == 0x01 0x008 4 1411 --- Lifetime Power-On
Resets 0x01 0x010 4 9891 --- Power-on Hours 0x01 0x018
6 23777035689 --- Logical Sectors Written 0x01 0x028 6
26752324966 --- Logical Sectors Read 0x01 0x038 6 9891
--- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 ---
Current Temperature 0x05 0x010 1 - --- Average Short
Term Temperature 0x05 0x018 1 - --- Average Long
Term Temperature 0x05 0x020 1 53 --- Highest
Temperature 0x05 0x028 1 13 --- Lowest Temperature
0x05 0x030 1 27 --- Highest Average Short Term
Temperature 0x05 0x038 1 27 --- Lowest Average Short
Term Temperature 0x05 0x040 1 - --- Highest Average
Long Term Temperature 0x05 0x048 1 - --- Lowest
Average Long Term Temperature 0x05 0x050 4 0 ---
Time in Over-Temperature 0x05 0x058 1 95 ---
Specified Maximum Operating Temperature 0x05 0x060 4 0
--- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = =
=== == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11) ID Size Value
Description 0x0003 2 0 R_ERR response for device-to-host
data FIS 0x0004 2 0 R_ERR response for host-to-device
data FIS 0x0006 2 0 R_ERR response for device-to-host
non-data FIS 0x0007 2 0 R_ERR response for host-to-device
non-data FIS 0x0009 2 43 Transition from drive PhyRdy to
drive PhyNRdy 0x000a 2 44 Device-to-host register FISes
sent due to a COMRESET 0x000f 2 0 R_ERR response for
host-to-device data FIS, CRC 0x0012 2 0 R_ERR response
for host-to-device non-data FIS, CRC 0x0001 2 0 Command
failed due to ICRC error
답변1
충돌 보고서의 메시지는 디스크에 sdb읽기 오류가 발생하여 잘못된 데이터를 반환했음을 나타냅니다. auto reallocate failed따라서 감지된 불량 블록을 교체하는 데 사용되었을 수 있는 예비 용량이 모두 사용되었음을 나타냅니다 .
sudo smartctl -x /dev/sdb이를 실행 하고 보고되는 내용을 확인 해야 합니다 .
sdb또한 디스크가 갑자기 완전히 고장나는 경우(때때로 SSD 고장이 발생하는 경우처럼) 에 대비하여 백업을 최신 상태로 유지해야 합니다 .
디스크가 수명을 다하고 있으므로 데이터를 분할하고 가능한 한 빨리 디스크를 교체해야 합니다.
ddrescueGNU(Debian/Ubuntu 저장소의 패키지)를 사용한 데이터 복구 시도가 실패gddrescue하고 이 실패한 디스크의 데이터가 필요하다고 가정하면 평판이 좋은 데이터 복구 센터에 문의하십시오.이 SATA SSD 손상을 복구하기 위해 소프트웨어나 하드웨어를 사용할 수 없으며 완전한 오류가 임박합니다.