논리 볼륨으로 구성된 ext3 파티션이 있습니다. 볼륨 그룹(8TB)은 3개의 PV(1* 4TB, 2* 2TB)로 구성됩니다. ext3 파티션은 볼륨 그룹의 유일한 파티션입니다.
Manjaro Linux에서 fstab을 사용하여 이 파티션을 폴더(/plex_media/)에 마운트했습니다. 모든 것이 예상대로 시작되고 로드됩니다. 그런데 갑자기 콘텐츠 복사를 시작하면 파티션이 읽기 전용으로 다시 마운트된 것처럼 보입니다. dmesg(아래에 붙여넣은 출력)에서 이를 볼 수 있지만 이러한 메시지를 해석하기에는 dmesg에 대한 경험이 충분하지 않습니다.
모든 디스크는 SMART를 지원하며 오류가 표시되지 않습니다(아래 참조). 로그를 삭제하고 tunef2s 및 e2fsck를 사용하여 다시 작성했습니다. dmesg의 모든 SATA 링크 다운 메시지 때문에 케이블 문제일 수도 있다는 느낌이 들지만 실제로 그 의미를 모르고 온라인 설명을 이해하지 못합니다.
나는 무엇을 해야할지 모르겠습니다. 제가 보기에는 설정에는 아무런 문제가 없습니다. 어떤 통찰력이라도 대단히 감사하겠습니다.
안정적인 테이블:
# <file system> <mount point> <type> <options> <dump> <pass>
UUID=d031b8a8-f4f3-46ab-8ed6-7586a561f095 /boot ext4 defaults,noatime 0 2
UUID=ce292a75-d067-4caa-9b6f-41658aa8acbb swap swap defaults,noatime 0 2
UUID=153b1d1e-97cb-4157-a5f8-16ea46309adc / ext4 defaults,noatime 0 1
UUID=7e967bc5-29ab-45ae-b0ff-e73d97874cfe /home ext4 defaults,noatime 0 2
#/dev/plex_media/plex_media /plex_media ext3 defaults,noatime 0 0
메시지 출력
[ 1645.470175] ata5.00: configured for UDMA/33
[ 1646.598486] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1646.598498] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1646.603513] ata5.00: configured for UDMA/33
[ 1647.588479] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1647.588490] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1647.593590] ata5.00: configured for UDMA/33
[ 1648.568480] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1648.568492] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1648.573498] ata5.00: configured for UDMA/33
[ 1649.561814] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1649.561827] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1649.566849] ata5.00: configured for UDMA/33
[ 1650.565192] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1650.565204] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1650.570360] ata5.00: configured for UDMA/33
[ 1651.551809] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1651.551820] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1651.556823] ata5.00: configured for UDMA/33
[ 1651.556982] sd 4:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 1651.556986] sd 4:0:0:0: [sda] tag#0 Sense Key : Aborted Command [current]
[ 1651.556989] sd 4:0:0:0: [sda] tag#0 Add. Sense: Scsi parity error
[ 1651.556994] sd 4:0:0:0: [sda] tag#0 CDB: Write(16) 8a 00 00 00 00 00 07 7a 7a a0 00 00 01 30 00 00
[ 1651.556997] print_req_error: I/O error, dev sda, sector 125467296
[ 1651.557134] Aborting journal on device dm-0-8.
[ 1651.566969] EXT4-fs error (device dm-0): ext4_journal_check_start:61: Detected aborted journal
[ 1651.566972] EXT4-fs (dm-0): Remounting filesystem read-only
[ 1651.574177] EXT4-fs error (device dm-0) in ext4_free_blocks:4942: Journal has aborted
[ 1651.578693] EXT4-fs error (device dm-0): ext4_journal_check_start:61: Detected aborted journal
[ 1651.578707] EXT4-fs error (device dm-0) in ext4_write_begin:1339: IO failure
[ 1651.583843] EXT4-fs error (device dm-0) in ext4_free_blocks:4942: Journal has aborted
[ 1651.588547] EXT4-fs error (device dm-0): ext4_journal_check_start:61: Detected aborted journal
[ 1651.588551] EXT4-fs error (device dm-0) in ext4_free_blocks:4942: Journal has aborted
[ 1652.885140] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1652.885152] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1652.890145] ata5.00: configured for UDMA/33
[ 1681.611201] EXT4-fs (dm-0): pa 0000000098646a44: logic 24576, phys. 991498240, len 2048
[ 1681.611206] EXT4-fs error (device dm-0): ext4_mb_release_inode_pa:3835: group 30258, free 1962, pa_free 1963
[ 1681.611247] EXT4-fs error (device dm-0): mb_free_blocks:1452: group 30258, inode 184205374: block 991500758:freeing already freed block (bit 6614); block bitmap corrupt.
[ 1681.611260] EXT4-fs error (device dm-0): ext4_mb_generate_buddy:744: group 30258, block bitmap and bg descriptor inconsistent: 19796 vs 19797 free clusters
[ 1681.611265] EXT4-fs (dm-0): pa 000000005320a0a3: logic 18432, phys. 991500288, len 2048
[ 1681.611267] EXT4-fs error (device dm-0): ext4_mb_release_inode_pa:3835: group 30258, free 1963, pa_free 1962
[ 1681.611412] EXT4-fs (dm-0): pa 00000000215c728f: logic 10240, phys. 991510528, len 2048
[ 1681.611414] EXT4-fs error (device dm-0): ext4_mb_release_inode_pa:3835: group 30258, free 2048, pa_free 2047
[ 1682.748458] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1682.748470] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1682.753459] ata5.00: configured for UDMA/33
[ 1684.048464] ata5.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1684.048475] ata5.01: SATA link down (SStatus 4 SControl 300)
[ 1684.055559] ata5.00: configured for UDMA/33
지능형 출력
$ sudo smartctl -a /dev/sdc
[sudo] password for aelsayed:
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.60-1-MANJARO] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WCAZA0851330
LU WWN Device Id: 5 0014ee 25a4aa68c
Firmware Version: 51.0AB51
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Aug 13 12:17:14 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (39180) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 378) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 198 195 051 Pre-fail Always - 997
3 Spin_Up_Time 0x0027 167 158 021 Pre-fail Always - 6625
4 Start_Stop_Count 0x0032 091 091 000 Old_age Always - 9853
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 21198
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5153
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 379
193 Load_Cycle_Count 0x0032 143 143 000 Old_age Always - 171431
194 Temperature_Celsius 0x0022 113 094 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 28
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ sudo smartctl -a /dev/sdb
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.60-1-MANJARO] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF)
Device Model: WDC WD20EARS-00MVWB0
Serial Number: WD-WMAZA0280349
LU WWN Device Id: 5 0014ee 60041fdb1
Firmware Version: 50.0AB50
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Tue Aug 13 12:17:17 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (37200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 424) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 166 159 021 Pre-fail Always - 6691
4 Start_Stop_Count 0x0032 091 091 000 Old_age Always - 9224
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 21032
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 5060
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 368
193 Load_Cycle_Count 0x0032 170 170 000 Old_age Always - 91513
194 Temperature_Celsius 0x0022 113 095 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 27
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ sudo smartctl -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.19.60-1-MANJARO] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue
Device Model: WDC WD40EZRZ-00GXCB0
Serial Number: WD-WCC7K6ZKKS6P
LU WWN Device Id: 5 0014ee 2bb9a65bf
Firmware Version: 80.00A80
User Capacity: 4.000.787.030.016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Tue Aug 13 12:17:19 2019 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (43680) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 463) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 209 169 021 Pre-fail Always - 4550
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 25
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1064
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 25
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 21
193 Load_Cycle_Count 0x0032 184 184 000 Old_age Always - 49880
194 Temperature_Celsius 0x0022 114 102 000 Old_age Always - 36
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 198 110 000 Old_age Always - 156166
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
답변1
이 버그는 수정되었습니다. SATA 포트 5가 작동하지 않는 것으로 나타났습니다. 방금 다른 포트로 변경했는데 지금은 잘 작동하고 있습니다. SATA 링크 다운에 대한 dmesg 메시지가 없습니다. 읽기 전용으로 다시 마운트되었기 때문에 하드 드라이브에 오류가 있는 것으로 표시되었으므로 fsck를 실행해야 했고 오류가 반환되지 않았습니다!