나는 전에 달리고 있었다 atop. 작동 중이었지만 종료 상태 53으로 종료되었습니다.
$ atop
$ echo $?
53
이것은 버그입니까 atop? 아니면 내 시스템에 문제가 있는 걸까요?
선제적인 추가 세부정보 :-)
커널 로그( dmesg)를 확인했습니다. 난 아무것도 못 찾았어구체적으로충격적이지만 다소 잘못된 내용이기도 합니다. 아래를 참조하세요.
이 노트북은 몇 달 동안 안정적으로 사용되었습니다. 커널은 "오염"되지 않았으므로 커널 WARN 또는 OOPS 메시지가 없습니다.
$ cat /proc/sys/kernel/tainted
0
$ rpm -q atop
atop-2.3.0-10.fc28.x86_64
$ uname -r # My kernel version
5.1.6-200.fc29.x86_64
dmesgatop최근에 컴퓨터를 잠자기 상태에서 깨워서 잠자기 전에 컴퓨터를 시작한 것을 상기시켜 줍니다.
dmesg또한 이 시간 동안 연결 상태가 좋지 않은 USB 스틱과의 연결이 끊어지기 때문에 USB 및 FAT 오류가 표시되는 경우도 있습니다.
일시 중지 상태에서 복구하는 동안 일부 하드웨어 메시지가 표시됩니다. 그러나 지난 몇 달 동안 사용자에게 눈에 띄는 잠자기/깨우기 문제가 발생하지 않았습니다.
초기 실수도 있었습니다 dmesg.
[40654.082396] PM: suspend exit
[40654.205336] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.8.10-fw-1.10.3.11.e.bseq
[40654.517627] Bluetooth: hci0: unexpected event for opcode 0xfc2f
[40654.534651] Bluetooth: hci0: Intel firmware patch completed and activated
[40655.519592] e1000e 0000:00:19.0 eno1: Detected Hardware Unit Hang:
TDH <0>
TDT <10>
next_to_use <10>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <10267d16b>
next_to_watch <1>
jiffies <10267d740>
next_to_watch.status <0>
MAC Status <80000>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
[40656.239991] Process accounting resumed
[40656.318355] e1000e: eno1 NIC Link is Down
...
[41013.654127] usb 2-2: USB disconnect, device number 43
[41013.901953] usb 2-2: new full-speed USB device number 46 using xhci_hcd
[41020.270316] FAT-fs (sdb4): Directory bread(block 22704) failed
[41020.270322] FAT-fs (sdb4): Directory bread(block 22705) failed
[41020.270325] FAT-fs (sdb4): Directory bread(block 22706) failed
[41020.270328] FAT-fs (sdb4): Directory bread(block 22707) failed
[41020.270331] FAT-fs (sdb4): Directory bread(block 22708) failed
[41020.270333] FAT-fs (sdb4): Directory bread(block 22709) failed
[41020.270336] FAT-fs (sdb4): Directory bread(block 22710) failed
[41020.270339] FAT-fs (sdb4): Directory bread(block 22711) failed
[41020.270354] FAT-fs (sdb4): Directory bread(block 22704) failed
[41020.270357] FAT-fs (sdb4): Directory bread(block 22705) failed
[41029.558085] usb 2-2: device descriptor read/64, error -110
[41029.780057] usb 2-2: device descriptor read/64, error -71
[41029.996102] usb 2-2: new full-speed USB device number 47 using xhci_hcd
[41030.110057] usb 2-2: device descriptor read/64, error -71
[41030.332052] usb 2-2: device descriptor read/64, error -71
[41030.434046] usb usb2-port2: attempt power cycle
[41031.061973] usb 2-2: new full-speed USB device number 48 using xhci_hcd
[41031.062086] usb 2-2: Device not responding to setup address.
[41031.266212] usb 2-2: Device not responding to setup address.
[41031.474101] usb 2-2: device not accepting address 48, error -71
[41031.588100] usb 2-2: new full-speed USB device number 49 using xhci_hcd
[41031.588294] usb 2-2: Device not responding to setup address.
[41031.794271] usb 2-2: Device not responding to setup address.
[41032.002095] usb 2-2: device not accepting address 49, error -71
[41032.002202] usb usb2-port2: unable to enumerate USB device
[41070.004040] usb 2-1: new high-speed USB device number 50 using xhci_hcd
[41075.638042] usb 2-1: device descriptor read/64, error -110
[41075.877302] usb 2-1: New USB device found, idVendor=0718, idProduct=063d, bcdDevice= 1.00
[41075.877309] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[41075.877313] usb 2-1: Product: Nano Pro
[41075.877316] usb 2-1: Manufacturer: Imation
[41075.877319] usb 2-1: SerialNumber: 0703335B0AF92D86
[41075.881530] usb-storage 2-1:1.0: USB Mass Storage device detected
[41075.882899] scsi host3: usb-storage 2-1:1.0
[41077.004052] scsi 3:0:0:0: Direct-Access Imation Nano Pro PMAP PQ: 0 ANSI: 4
[41077.005015] sd 3:0:0:0: Attached scsi generic sg1 type 0
[41078.366583] sd 3:0:0:0: [sdc] 15116736 512-byte logical blocks: (7.74 GB/7.21 GiB)
[41078.366732] sd 3:0:0:0: [sdc] Write Protect is off
[41078.366735] sd 3:0:0:0: [sdc] Mode Sense: 23 00 00 00
[41078.366935] sd 3:0:0:0: [sdc] No Caching mode page found
[41078.366939] sd 3:0:0:0: [sdc] Assuming drive cache: write through
[41078.389637] sdc: sdc1 sdc2 sdc3 sdc4
[41078.392305] sd 3:0:0:0: [sdc] Attached SCSI removable disk
이전 오류:
$ journalctl -o short-monotonic -k -p err
[ 14.953318] alan-laptop kernel: i801_smbus 0000:00:1f.3: Failed to enable SMBus PCI device (-16)
[ 15.919042] alan-laptop kernel: uvcvideo: Failed to query (GET_INFO) UVC control 3 on unit 1: -32 (exp. 1).
[ 15.974276] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[ 19.812805] alan-laptop kernel: db_root: cannot open: /etc/target
[ 35.219443] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
...
[19625.693967] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[20606.292276] alan-laptop kernel: ACPI Error: Thread 3649118016 cannot release Mutex [PATM] acquired by thread 2284756800 (20190215/exmutex-382)
[20606.292282] alan-laptop kernel: ACPI Error: Aborting method \_SB.PCI0.LPCB.ECDV._Q66 due to previous error (AE_AML_NOT_OWNER) (20190215/psparse-53>
[20609.491788] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[22006.616549] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[28469.301081] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[28472.604260] alan-laptop kernel: Bluetooth: hci0: command 0x0c56 tx timeout
[30297.940165] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
[30355.700904] alan-laptop kernel: mmc0: error -110 doing runtime resume
[30355.939525] alan-laptop kernel: Bluetooth: hci0: unexpected event for opcode 0xfc2f
답변1
이것은 의 버그입니다 atop. 치명적인 오류가 발생하면 오류 메시지를 인쇄할 수 없습니다. 나는 가지고있다버그를 보고했습니다프로젝트 꼭대기에.
오류는 마운트된 USB로 atop디렉토리( )를 변경한 후 실행했는데 cd... 마운트된 USB와의 연결이 끊어졌습니다.
src/atop$ grep -r 'exit[ ]*[(]' .
...
various.c
577: exit(13);
590: exit(exitcode);
...
src/atop$ grep -r '53' .
...
photosyst.c
101:** Revision 1.16 2004/05/06 09:53:31 gerlof
107:** Revision 1.14 2003/07/08 13:53:21 gerlof
305: cleanstop(53);
...
기능에서 photosyst():
if ( getcwd(origdir, sizeof origdir) == NULL)
{
perror("save current dir");
cleanstop(53);
}
이해합니다atop 노력하다오류 메시지를 인쇄합니다. 그런데 cleanstop()원래 화면을 복원 하고 싶어요 . 따라서 오류 메시지가 제거됩니다 :-).