☰

ifconfig를 사용하기 전에 본 것처럼 "ip link"에서 ipv4 주소를 어떻게 얻나요?

tag-icon • tag-icon networking iproute ifconfig ipv4
ifconfig를 사용하기 전에 본 것처럼 "ip link"에서 ipv4 주소를 어떻게 얻나요?

내가 얻은 IP 주소를 얻기 위해 ip를 실행하면

$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DORMANT group default qlen 1000
    link/ether 6c:88:14:ba:cb:cc brd ff:ff:ff:ff:ff:ff

이는 IPv4 주소는 아니지만 ifconfig표시됩니다.

$ sudo /sbin/ifconfig      
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 1102801  bytes 74417671 (70.9 MiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1102801  bytes 74417671 (70.9 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp3s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 10.7.7.57  netmask 255.255.252.0  broadcast 10.7.7.255
        inet6 fe80::440:3794:6794:8b1b  prefixlen 64  scopeid 0x20<link>
        inet6 2620:0:28a2:4010:2:2:8c75:f8a1  prefixlen 128  scopeid 0x0<global>
        ether 6c:88:14:ba:cb:cc  txqueuelen 1000  (Ethernet)
        RX packets 32743430  bytes 48351612590 (45.0 GiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 14856403  bytes 1590947780 (1.4 GiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

권장하지 않고 신뢰하지 않는 상황에 빠지지 않고 ipv4 정보를 얻으려면 어떻게 해야 합니까 ifconfig?

답변1

분명히 ipMAC 주소(현재 ip link(장치) 인터페이스에 있음)와 네트워크가 파손되었습니다 ip address. 이 명령은 ip address네트워크 주소를 표시합니다.

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 6c:88:14:ba:cb:cc brd ff:ff:ff:ff:ff:ff
    inet 10.7.7.57/22 brd 10.7.7.255 scope global dynamic noprefixroute wlp3s0
       valid_lft 1203509sec preferred_lft 1203509sec
    inet6 2620:0:28a2:4010:2:2:8c75:f8a1/128 scope global dynamic noprefixroute 
       valid_lft 1203512sec preferred_lft 598712sec
    inet6 fe80::440:3794:6794:8b1b/64 scope link noprefixroute 
       valid_lft forever preferred_lft forever

-br이는 보다 간결하고 사용자 친화적인(ief) 형식으로 볼 수 있습니다.

$ ip -4 -br addr show
lo               UNKNOWN        127.0.0.1/8
wlp3s0           UP             10.7.7.57/22

-o또는 한 줄( ) 로 볼 수도 있습니다 .

$ ip -o address
1: lo    inet 127.0.0.1/8 scope host lo\       valid_lft forever preferred_lft forever
1: lo    inet6 ::1/128 scope host \       valid_lft forever preferred_lft forever
3: wlp3s0    inet 10.7.7.57/22 brd 10.7.7.255 scope global dynamic noprefixroute wlp3s0\       valid_lft 1202464sec preferred_lft 1202464sec
3: wlp3s0    inet6 2620:0:28a2:4010:2:2:8c75:f8a1/128 scope global dynamic noprefixroute \       valid_lft 1202466sec preferred_lft 597666sec
3: wlp3s0    inet6 fe80::440:3794:6794:8b1b/64 scope link noprefixroute \       valid_lft forever preferred_lft forever

관련 정보