☰

내 vocore2에 이더넷 IP 주소가 없습니다

tag-icon • tag-icon bridge openwrt
내 vocore2에 이더넷 IP 주소가 없습니다

방금 플래시를 터뜨렸어요보코레 2uopenwrt 18.06.1을 사용하고 전화기의 무선 액세스 포인트를 설정하는 동안 이더넷 케이블을 사용하여 네트워크에 연결합니다. 여기에 이미지 설명을 입력하세요. AP가 작동하고 네트워크에 연결되어 있지만 내 전화기의 IP가 다른 라우터의 서브넷에 있습니다. 그리고 내 vocore2에는 IP가 할당되어 있지 않으므로 SSH를 통해 액세스할 수 없습니다. 직렬 터미널을 사용하여 vocore2에 연결한 후 ping 8.8.8.8도 실패했습니다. vocore2가 라우터에서 IP를 얻고 네트워크를 설정하도록 하려면 어떻게 해야 합니까?

    root@OpenWrt:/etc/config# ifconfig
    apcli0    Link encap:Ethernet  HWaddr BA:D8:12:07:01:71
              inet6 addr: fe80::b8d8:12ff:fe07:171/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

    br-lan    Link encap:Ethernet  HWaddr B8:D8:12:67:01:72
              inet addr:192.168.61.1  Bcast:192.168.61.255  Mask:255.255.255.0
              inet6 addr: fd43:4277:1a20::1/60 Scope:Global
              inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:16891 errors:0 dropped:0 overruns:0 frame:0
              TX packets:2404 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:1181826 (1.1 MiB)  TX bytes:477837 (466.6 KiB)

    eth0      Link encap:Ethernet  HWaddr B8:D8:12:67:01:72
              inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:2773 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 B)  TX bytes:736242 (718.9 KiB)
              Interrupt:5

    eth0.1    Link encap:Ethernet  HWaddr B8:D8:12:67:01:72
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:1067 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 B)  TX bytes:145725 (142.3 KiB)

    eth0.2    Link encap:Ethernet  HWaddr B8:D8:12:67:01:72
              inet6 addr: fe80::bad8:12ff:fe67:172/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:0 errors:0 dropped:0 overruns:0 frame:0
              TX packets:1692 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:0 (0.0 B)  TX bytes:577096 (563.5 KiB)

    lo        Link encap:Local Loopback
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:65536  Metric:1
              RX packets:886 errors:0 dropped:0 overruns:0 frame:0
              TX packets:886 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:64988 (63.4 KiB)  TX bytes:64988 (63.4 KiB)

    ra0       Link encap:Ethernet  HWaddr B8:D8:12:67:01:71
              inet6 addr: fe80::bad8:12ff:fe67:171/64 Scope:Link
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:27199 errors:14 dropped:0 overruns:0 frame:0
              TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000
              RX bytes:2189856 (2.0 MiB)  TX bytes:441570 (431.2 KiB)
              Interrupt:6

네트워크 구성

    root@OpenWrt:/etc/config# uci show network
    network.loopback=interface
    network.loopback.ifname='lo'
    network.loopback.proto='static'
    network.loopback.ipaddr='127.0.0.1'
    network.loopback.netmask='255.0.0.0'
    network.globals=globals
    network.globals.ula_prefix='fd43:4277:1a20::/48'
    network.lan=interface
    network.lan.type='bridge'
    network.lan.ifname='eth0.1'
    network.lan.proto='static'
    network.lan.ipaddr='192.168.61.1'
    network.lan.netmask='255.255.255.0'
    network.lan.ip6assign='60'
    network.lan_dev=device
    network.lan_dev.name='eth0.1'
    network.lan_dev.macaddr='b8:d8:12:67:01:72'
    network.wan=interface
    network.wan.ifname='eth0.2'
    network.wan.force_link='1'
    network.wan.proto='dhcp'
    network.wwan=interface
    network.wwan.ifname='apcli0'
    network.wwan.proto='dhcp'
    network.@switch[0]=switch
    network.@switch[0].name='switch0'
    network.@switch[0].reset='1'
    network.@switch[0].enable_vlan='1'
    network.@switch_vlan[0]=switch_vlan
    network.@switch_vlan[0].device='switch0'
    network.@switch_vlan[0].vlan='1'
    network.@switch_vlan[0].ports='0 2 6t'

답변1

다음 구성을 사용하여 수정되었습니다.

network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd15:39fa:4166::/48'
network.lan=interface
network.lan.ifname='eth0.1'
network.lan.force_link='1'
network.lan.macaddr='b8:d8:12:67:01:71'
network.lan.type='bridge'
network.lan.proto='static'
network.lan.ipaddr='192.168.61.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.force_link='1'
network.wan.macaddr='b8:d8:12:67:01:72'
network.wan.proto='dhcp'
network.wan6=interface
network.wan6.ifname='eth0.2'
network.wan6.proto='dhcpv6'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='1 2 3 4 6t'
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device='switch0'
network.@switch_vlan[1].vlan='2'
network.@switch_vlan[1].ports='0 6t'

관련 정보