dmesg는 이 USB SSD에 대해 무엇을 알려줍니까?

dmesg는 이 USB SSD에 대해 무엇을 알려줍니까?

RPi4에서 Ubuntu Mate로 부팅할 때 드라이브가 제대로 작동합니다. 새로운 RPi4에서 Berryboot와 함께 사용하기 전에 다시 포맷했습니다. BB 설치 중에 "제거할 수 없습니다..."라는 오류 메시지가 표시되었지만 설치를 계속했더니 Raspbian 설치가 성공한 것처럼 보였습니다. 하지만 재부팅할 때 일련의 오류 메시지가 표시되고 제공된 콘솔 모드로 들어갈 수도 없었습니다. 그냥 반복되었습니다. 나는 그것을 삭제하고 다시 포맷하고 Raspbian 이미지를 직접 플래시하는 것을 고려하고 berryboot를 포기했습니다. 하지만 이제는 Manjaro Gnome 데스크탑에서 액세스할 수 없습니다. 디스크나 Gparted에는 아무것도 표시되지 않습니다. 그러나 dmesg(아래)의 로그는 시스템이 그 존재를 인식하고 방법을 찾으려고 노력하고 있음을 나타내는 것 같습니다. 그러나 이것은 내 이해의 한계이며 더 잘 아는 사람이 알 수 있기를 바랍니다. SSD가 벽돌이 되었거나 복원할 수 있는 방법이 있으면 연락주세요. (그런데 케이블이 아닌 것은 확실합니다!)

[27958.059701] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27962.563005] usb 2-1: Device not responding to setup address.
[27962.773004] usb 2-1: Device not responding to setup address.
[27962.979681] usb 2-1: device not accepting address 97, error -71
[27964.829787] usb 2-1: Device not responding to setup address.
[27965.039755] usb 2-1: Device not responding to setup address.
[27965.246367] usb 2-1: device not accepting address 98, error -71
[27965.246455] usb usb2-port1: attempt power cycle
[27969.619815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27977.136538] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27981.309911] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27985.349948] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.173343] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.733351] usb 2-1: new SuperSpeed Gen 1 USB device number 100 using xhci_hcd
[27992.750695] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[27992.750701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27992.750705] usb 2-1: Product: USB3.1 TO NVME SSD
[27992.750708] usb 2-1: Manufacturer: Liangteng
[27992.750711] usb 2-1: SerialNumber: DD20180910888
[27992.755322] scsi host13: uas
[27992.755602] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[27992.756009] sd 13:0:0:0: Attached scsi generic sg2 type 0
[27994.536635] usb 2-1: USB disconnect, device number 100
[27994.536829] sd 13:0:0:0: tag#5 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[27994.536836] sd 13:0:0:0: tag#5 CDB: Test Unit Ready 00 00 00 00 00 00
[27994.740047] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.740053] sd 13:0:0:0: [sdb] Sense not available.
[27994.940027] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.940035] sd 13:0:0:0: [sdb] Sense not available.
[27995.020071] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27995.020076] sd 13:0:0:0: [sdb] 0-byte physical blocks
[27995.086718] sd 13:0:0:0: [sdb] Write Protect is off
[27995.086724] sd 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
[27995.153389] sd 13:0:0:0: [sdb] Asking for cache data failed
[27995.153395] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[27995.583395] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.583400] sd 13:0:0:0: [sdb] Sense not available.
[27995.783396] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.783402] sd 13:0:0:0: [sdb] Sense not available.
[27996.116733] sd 13:0:0:0: [sdb] Attached SCSI disk
[28000.403421] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28004.446787] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28008.620161] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28012.660199] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28016.833566] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28022.540260] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28029.777038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28039.027104] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28045.670502] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28050.317265] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28054.357241] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28055.913914] usb 2-1: new SuperSpeed Gen 1 USB device number 101 using xhci_hcd
[28061.057336] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28061.057342] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28061.227242] usb 2-1: USB disconnect, device number 101
[28065.570677] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28069.744041] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28077.630789] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28081.804158] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28085.844197] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28090.017597] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28094.057605] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28098.230975] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28102.271013] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28112.761109] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28117.407815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28121.751190] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28131.897945] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28135.937988] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28142.054706] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28146.768079] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28154.911501] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28158.951530] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28163.464900] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28165.848241] usb 2-1: new SuperSpeed Gen 1 USB device number 103 using xhci_hcd
[28165.865580] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28165.865586] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28165.865590] usb 2-1: Product: USB3.1 TO NVME SSD
[28165.865593] usb 2-1: Manufacturer: Liangteng
[28165.865596] usb 2-1: SerialNumber: DD20180910888
[28165.870697] scsi host13: uas
[28165.871387] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[28165.872223] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28165.873122] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28165.873128] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28165.873268] sd 13:0:0:0: [sdb] Write Protect is off
[28165.873272] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28165.873515] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28165.873756] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28166.068149] usb 2-1: USB disconnect, device number 103
[28166.068323] usb 2-1: cmd cmplt err -108
[28166.068331] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
[28166.068391] sd 13:0:0:0: tag#4 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[28166.068396] sd 13:0:0:0: tag#4 CDB: Test Unit Ready 00 00 00 00 00 00
[28166.268276] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.268281] sd 13:0:0:0: [sdb] Sense not available.
[28166.468254] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.468259] sd 13:0:0:0: [sdb] Sense not available.
[28166.554956] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28166.554962] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28166.728277] sdb: detected capacity change from 128035676160 to 0
[28166.994947] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.994952] sd 13:0:0:0: [sdb] Sense not available.
[28167.201616] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28167.201622] sd 13:0:0:0: [sdb] Sense not available.
[28167.454955] sd 13:0:0:0: [sdb] Attached SCSI disk
[28175.214997] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28186.798446] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28187.528446] usb 2-1: new SuperSpeed Gen 1 USB device number 104 using xhci_hcd
[28187.545781] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28187.545789] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28187.545794] usb 2-1: Product: USB3.1 TO NVME SSD
[28187.545798] usb 2-1: Manufacturer: Liangteng
[28187.545803] usb 2-1: SerialNumber: DD20180910888
[28187.551139] scsi host13: uas
[28187.551951] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[28187.552706] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28187.553606] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28187.553612] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28187.553751] sd 13:0:0:0: [sdb] Write Protect is off
[28187.553756] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28187.553960] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28187.554163] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28189.415076] usb 2-1: USB disconnect, device number 104
[28189.415246] usb 2-1: cmd cmplt err -108
[28189.415254] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
[28189.415333] sd 13:0:0:0: tag#3 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[28189.415338] sd 13:0:0:0: tag#3 CDB: Test Unit Ready 00 00 00 00 00 00
[28189.615153] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28189.615159] sd 13:0:0:0: [sdb] Sense not available.
[28189.815156] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28189.815162] sd 13:0:0:0: [sdb] Sense not available.
[28189.898477] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28189.898481] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28190.071820] sdb: detected capacity change from 128035676160 to 0
[28190.338477] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28190.338483] sd 13:0:0:0: [sdb] Sense not available.
[28190.538500] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28190.538506] sd 13:0:0:0: [sdb] Sense not available.
[28190.791840] sd 13:0:0:0: [sdb] Attached SCSI disk
[28199.471894] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28204.665275] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28209.008647] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28212.048663] usb 2-1: new SuperSpeed Gen 1 USB device number 105 using xhci_hcd
[28212.066008] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28212.066017] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28212.066023] usb 2-1: Product: USB3.1 TO NVME SSD
[28212.066028] usb 2-1: Manufacturer: Liangteng
[28212.066032] usb 2-1: SerialNumber: DD20180910888
[28212.071230] scsi host13: uas
[28212.071903] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[28212.072654] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28212.073388] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28212.073394] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28212.073520] sd 13:0:0:0: [sdb] Write Protect is off
[28212.073525] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28212.073729] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28212.073931] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28216.688717] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28216.688738] usb 2-1: USB disconnect, device number 105
[28216.688988] sd 13:0:0:0: [sdb] tag#23 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[28216.688994] sd 13:0:0:0: [sdb] tag#23 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[28216.689046] sd 13:0:0:0: [sdb] tag#23 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[28216.689051] sd 13:0:0:0: [sdb] tag#23 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[28216.689054] print_req_error: 18 callbacks suppressed
[28216.689059] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689064] buffer_io_error: 1 callbacks suppressed
[28216.689066] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689183] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689189] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689202] ldm_validate_partition_table(): Disk read failed.
[28216.689219] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689223] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689240] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689243] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689260] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689263] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689269]  sdb: unable to read partition table
[28216.955426] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28216.955432] sd 13:0:0:0: [sdb] Sense not available.
[28217.155407] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28217.155412] sd 13:0:0:0: [sdb] Sense not available.
[28217.235418] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28217.235423] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28217.408746] sd 13:0:0:0: [sdb] Attached SCSI disk
[28223.502118] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28232.452185] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28236.795550] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28240.835596] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28246.818991] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28251.329032] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28258.342429] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28265.469159] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28271.999228] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28282.249310] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28295.102764] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28297.522962] usb 2-1: Device not responding to setup address.
[28297.732737] usb 2-1: Device not responding to setup address.
[28297.939416] usb 2-1: device not accepting address 106, error -71
[28298.959461] usb 2-1: Device not responding to setup address.
[28299.169465] usb 2-1: Device not responding to setup address.
[28299.376069] usb 2-1: device not accepting address 107, error -71
[28299.376158] usb usb2-port1: attempt power cycle
[28301.392758] usb 1-1: new high-speed USB device number 66 using xhci_hcd
[28309.569560] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28313.609589] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28328.603066] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28336.559807] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28339.803151] usb 2-1: new SuperSpeed Gen 1 USB device number 109 using xhci_hcd
[28339.820599] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28339.820605] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28339.820609] usb 2-1: Product: USB3.1 TO NVME SSD
[28339.820612] usb 2-1: Manufacturer: Liangteng
[28339.820615] usb 2-1: SerialNumber: DD20180910888
[28339.828404] scsi host13: uas
[28339.829118] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[28339.830171] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28339.830772] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28339.830778] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28339.830910] sd 13:0:0:0: [sdb] Write Protect is off
[28339.830915] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28339.831193] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28339.831534] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28339.865797]  sdb: sdb1 sdb2
[28339.866811] sd 13:0:0:0: [sdb] Attached SCSI disk
[28340.049781] usb 2-1: USB disconnect, device number 109
[28340.051647] sd 13:0:0:0: [sdb] Synchronizing SCSI cache
[28340.249809] sd 13:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28346.913236] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28351.292797] proc: Bad value for 'hidepid'
[28351.328456] audit: type=1130 audit(1616687832.662:182): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[28355.206641] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28361.540038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28365.580058] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28369.753445] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28399.906129] audit: type=1131 audit(1616687881.238:183): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'

         [27949.779616] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27958.059701] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27962.563005] usb 2-1: Device not responding to setup address.
[27962.773004] usb 2-1: Device not responding to setup address.
[27962.979681] usb 2-1: device not accepting address 97, error -71
[27964.829787] usb 2-1: Device not responding to setup address.
[27965.039755] usb 2-1: Device not responding to setup address.
[27965.246367] usb 2-1: device not accepting address 98, error -71
[27965.246455] usb usb2-port1: attempt power cycle
[27969.619815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27977.136538] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27981.309911] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27985.349948] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.173343] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.733351] usb 2-1: new SuperSpeed Gen 1 USB device number 100 using xhci_hcd
[27992.750695] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[27992.750701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27992.750705] usb 2-1: Product: USB3.1 TO NVME SSD
[27992.750708] usb 2-1: Manufacturer: Liangteng
[27992.750711] usb 2-1: SerialNumber: DD20180910888
[27992.755322] scsi host13: uas
[27992.755602] scsi 13:0:0:0: Direct-Access     ITHOO    Tech             0204 PQ: 0 ANSI: 6
[27992.756009] sd 13:0:0:0: Attached scsi generic sg2 type 0
[27994.536635] usb 2-1: USB disconnect, device number 100
[27994.536829] sd 13:0:0:0: tag#5 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[27994.536836] sd 13:0:0:0: tag#5 CDB: Test Unit Ready 00 00 00 00 00 00
[27994.740047] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.740053] sd 13:0:0:0: [sdb] Sense not available.
[27994.940027] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.940035] sd 13:0:0:0: [sdb] Sense not available.
[27995.020071] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27995.020076] sd 13:0:0:0: [sdb] 0-byte physical blocks
[27995.086718] sd 13:0:0:0: [sdb] Write Protect is off
[27995.086724] sd 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
[27995.153389] sd 13:0:0:0: [sdb] Asking for cache data failed
[27995.153395] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[27995.583395] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.583400] sd 13:0:0:0: [sdb] Sense not available.
[27995.783396] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.783402] sd 13:0:0:0: [sdb] Sense not available.
[27996.116733] sd 13:0:0:0: [sdb] Attached SCSI disk
[28000.403421] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28004.446787] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28008.620161] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28012.660199] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28016.833566] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28022.540260] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28029.777038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28039.027104] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28045.670502] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28050.317265] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28054.357241] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28055.913914] usb 2-1: new SuperSpeed Gen 1 USB device number 101 using xhci_hcd
[28061.057336] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28061.057342] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28061.227242] usb 2-1: USB disconnect, device number 101

관련 정보