WLAN을 설정했지만 Wi-Fi를 통해 핑할 수 없습니다

wlan0구성을 설정했습니다 ( bcm43블랙리스트에서 주석 처리 해제됨).

root@NanoPC-T2:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 5e:a5:4f:cc:83:8a
          inet addr:195.165.101.232  Bcast:195.165.101.255  Mask:255.255.255.0
          inet6 addr: fe80::7ca8:5fff:fecc:738a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:21331 errors:0 dropped:11440 overruns:0 frame:0
          TX packets:390 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1734079 (1.7 MB)  TX bytes:64331 (64.3 KB)
          Interrupt:48

ip6tnl0   Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
          NOARP  MTU:1452  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3958 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3958 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:293200 (293.2 KB)  TX bytes:293200 (293.2 KB)

sit0      Link encap:IPv6-in-IPv4
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

usb0      Link encap:Ethernet  HWaddr e2:47:73:46:b9:8f
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr 15:a1:a2:a3:c5:4e
          inet6 addr: fe80::25d4:a2ff:fea3:c54e/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:468 (468.0 B)

그리고 또한 설정/etc/network/interfaces

 cat /etc/network/interfaces
auto lo eth0
iface lo inet loopback
iface eth0 inet static
address 195.165.101.232
netmask 255.255.255.0
gateway 195.165.101.254

iface wlan0 inet static
address 195.165.101.232
netmask 255.255.255.0
gateway 195.165.101.254
wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf  

그리고wpa_supplicant.conf

 cat /etc/wpa_supplicant/wpa_supplicant.conf
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=CN
network={
ssid="V01"
psk="123456"
proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP
auth_alg=OPEN
}  

저도 똑같이 하는데 ifconfig wlan0 up이더넷 연결을 끊으면 Wi-Fi에서 IP에 연결하거나 핑할 수 없습니다.

nmcli c
NAME      UUID                                  TYPE             DEVICE
V01    0c4435f2-7301-8574-9b1b-deb7fd2a7603  802-11-wireless  --
V1 1  80b21422-c7ea-568c-8b4c-6f1d8a9dc9f8  802-11-wireless  --