내 키보드의 WiFi LED는 일반적으로 꺼져 있을 때는 주황색이고 켜져 있을 때는 파란색이어야 하는데 항상 주황색이어서 불편합니다.
다음은 내가 유용하다고 생각한 몇 가지 결과입니다.
root@Machine:~# uname -a
Linux Machine 4.9.0-kali4-amd64 #1 SMP Debian 4.9.30-2kali1 (2017-06-22) x86_64 GNU/Linux
root@Machine:~# lspci | grep Wireless
44:00.0 Network controller: Broadcom Limited BCM4313 802.11bgn Wireless Network Adapter (rev 01)
root@Machine:~# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether a2:b2:d6:d5:4a:b0 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20 memory 0xd4800000-d4820000
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
loop txqueuelen 1 (Local Loopback)
RX packets 236821 bytes 65224834 (62.2 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 236821 bytes 65224834 (62.2 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.6 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::7670:459e:2cde:75ea prefixlen 64 scopeid 0x20<link>
inet6 fd9c:c172:b03b:ce00:204c:8ad8:2f5:d85b prefixlen 64 scopeid 0x0<global>
ether 26:26:10:c2:d4:f0 txqueuelen 1000 (Ethernet)
RX packets 111523 bytes 113324698 (108.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 112290 bytes 26144479 (24.9 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root@Machine:~# iwconfig
wlan0 IEEE 802.11 ESSID:"3bdo"
Mode:Managed Frequency:2.422 GHz Access Point: 9C:C1:72:B0:3B:D4
Bit Rate=65 Mb/s Tx-Power=19 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=60/70 Signal level=-50 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:275 Invalid misc:1391 Missed beacon:0
lo no wireless extensions.
eth0 no wireless extensions.
추신: 이전에 설치했지만 broadcom-sta-dkms
매우 문제가 많았기 때문에 삭제했습니다(Wi-Fi 비밀번호를 계속해서 요구하여 라우터에 액세스할 수 없고 모니터 모드를 켤 수 없습니다).broadcom-sta-common
broadcom-sta-source
답변1
문제는 내가 사용하고 있던 모듈에 있었습니다. 모듈을 에서 로 변경하면 다음 명령을 실행하여 문제가 brcmsmac
해결되었습니다 ( 에 추가한 후 ).wl
deb http://httpredir.debian.org/debian/ stretch main contrib non-free
/etc/apt/sources.list
apt-get update
apt-get install linux-image-$(uname -r|sed 's,[^-]*-[^-]*-,,') linux-headers-$(uname -r|sed 's,[^-]*-[^-]*-,,') broadcom-sta-dkms
modprobe -r b44 b43 b43legacy ssb brcmsmac bcma
modprobe wl