dmesggnome 데스크탑을 통해 연결하려고 하면 출력은 다음과 같습니다.
[ 4162.708769] R8188EU: INFO assoc success
[ 4165.713425] R8188EU: INFO ap recv disassoc reason code(2) sta:f8:3d:ff:ed:3b:b7
[ 4165.716173] R8188EU: INFO sta recv deauth reason code(6) sta:f8:3d:ff:ed:3b:b7, ignore = 0
[ 4165.720651] R8188EU: INFO indicate disassoc
Debian 8을 새로 설치하고 TP-Link 웹사이트에서 Linux 드라이버를 다운로드하세요. make, make installwlan0을 사용할 수 있는 것으로 나타납니다.
# ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 60:e3:27:15:fd:03
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:232 overruns:0 frame:0
TX packets:0 errors:0 dropped:2 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5320 (5.1 KiB) TX bytes:6280 (6.1 KiB)
무엇이 잘못되었고 어떻게 해결하는지 아는 사람이 있나요?
편집하다:
소스에서 컴파일을 시도했는데 재부팅 후 표시되는 내용은 다음과 같습니다(무선 액세스 포인트가 무선 네트워크 목록에 표시되지 않아 여전히 WiFi를 통해 인터넷에 연결할 수 없음).
[ 8.179429] EEPROM ID = 0x8129
[ 8.180503] usbcore: registered new interface driver r8188eu
[ 8.454849] cfg80211: Calling CRDA to update world regulatory domain
[ 8.517110] cfg80211: World regulatory domain updated:
[ 8.517119] cfg80211: DFS Master region: unset
[ 8.517123] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.517131] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.517138] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 8.517144] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.517149] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 8.517155] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 8.517160] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 8.517165] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 8.517170] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 8.548684] r8188eu 2-1:1.0: firmware: direct-loading firmware rtlwifi/rtl8188eufw.bin
[ 8.548720] R8188EU: Firmware Version 11, SubVersion 1, Signature 0x88e1
[ 8.926288] MAC Address = 60:e3:27:15:fd:03
[ 8.930721] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.238268] R8188EU: INFO indicate disassoc
[ 10.335372] R8188EU: INFO assoc success
[ 10.335443] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 10.794016] RPC: Registered named UNIX socket transport module.
[ 10.794025] RPC: Registered udp transport module.
[ 10.794030] RPC: Registered tcp transport module.
[ 10.794034] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.826250] FS-Cache: Loaded
[ 10.845544] FS-Cache: Netfs 'nfs' registered for caching
[ 10.903147] Installing knfsd (copyright (C) 1996 [email protected]).
[ 14.360757] tg3 0000:3f:00.0: irq 41 for MSI/MSI-X
[ 15.754090] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
편집하다:
출력 cat과lsusb
# cat /proc/sys/net/ipv6/conf/all/disable_ipv6
0
# lsusb
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0bda:8179 Realtek Semiconductor Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 002: ID 413c:2107 Dell Computer Corp.
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub